|
Silver Member Username: SatopiaPost Number: 489 Registered: Feb-08 | Free Trial effective immediately till Sunday, 10th. October, 2010 Server Address: fenfu.dynsite.net Username and Password: ftabeta.com Port: 10010. Usable on all receivers supported by NFPS. Enjoy. |
|
Silver Member Username: MrgregPost Number: 569 Registered: Dec-07 | This NFPS is a load of crap.You keep letting all these people sign up and it will be just as bad as any other Iks receiver Up & Down as they have already started to do this. |
|
Bronze Member Username: Xhounddog66Post Number: 42 Registered: Aug-08 | Hey Greg, I have used NFPS for 2 months and I have not had any problems with it at all. If it had an EPG it would be even better. |
|
Silver Member Username: MrgregPost Number: 570 Registered: Dec-07 | Hey,ted No epg is like having no TV to me anyway. |
|
Bronze Member Username: Xhounddog66Post Number: 43 Registered: Aug-08 | I understand that completely. |
|
Platinum Member Username: NydasPost Number: 19847 Registered: Jun-06 | step by step for cw700 and 800 nfps STEP BY STEP INSTRUCTIONS SETTING UP YOUR CAPTIVEWORKS 700 FOR NFPS DOWNLOAD THE CAPTIVEWORKS FILES .rar or .zip You need to download the file Captiveworks1.zip or .rar and then extract the files. You need only be concerned with two files the rq-sssp-client.exe and the rq-sssp-client.conf Only the rq-sssp-client.conf file will require any editing. VERIFY YOUR COM PORT To check your com port go to control panel > system > device manager > click the plus sign on PORTS and you will see COM(port#) this port # is the number that must be in the rq-sssp-client.conf file. Next right click on the COM (port#) and click on properties click on the tab port settings and they should read 15200 8 none 1 none if they are different then use the drop down menu to change them. EDIT YOUR rq-sssp-client.conf file Open the file in NOTEPAD - In notepad when you click on open and get the open dialogue box in file type drop down menu select ALL FILES otherwise you will not see this .conf file as notepad defaults to .txt files. Once open in notepad, go to the line that says serial_port=COM1 and if your COM PORT is not 1 then change the number to match the port number shown in device manager. Edit the newcamd line The last line of the rq-sssp-client.conf file a sample of which is below will require editing. You need to replace whatever is after the // with your nfps access code and then once again replace whatever is after the : with your access code After your 2nd access code be sure it reads @fenfu.dynsite.net and then after the : the port needs to be 10010 Your file should look just like this example except you need to use the access code you received from nfps to replace ACCESSCODE####. Do not remove the : between the two access codes or between net and the port number 10010. There are no spaces between any of the fields in this file. EXAMPLE card_server_url_1=newcamd://ACCESSCODE####:ACCESSCODE####@fenfu.dynsite.net:1001 0/6103403445406970987123412134 Once you have edited this file you need to save it as a .conf file. In NOTEPAD go to File > Save AS File name should be: rq-sssp-client.conf Save as type should be: All Files Encoding should be: ANSI Click on SAVE PLACEMENT OF THESE FILES IN YOUR PC Create a NEW FOLDER on your C drive or any partition you wish. I named the new folder CW but you can call it anything you wish. Either save the file you edited in NOTEPAD into this NEW FOLDER or copy the edited file from where you saved it and place it in this NEW FOLDER. Next copy the file rq-sssp-client.exe into the same NEW FOLDER. NOTE: BOTH OF THESE FILES MUST BE IN THE SAME FOLDER ON YOUR PC TO WORK TO SIMPLIFY STARTING THE PROTOCOL Each time you shut down your PC you will have to restart the file rq-sssp-client.exe - To simplify this task go to the NEW FOLDER where the file rq-sssp-client.exe is and right click on the file and select create a shortcut. After the shortcut shows up in the folder drag and drop it onto your quick launch bar. Now you can easily start the protocol with a single click of your mouse. . CONNECT UP YOUR CW700 Attach the cable from your dish (diseqc switch) to your CW700 and scan in both 110 and 119 and saved the channels Next connect your CW700 to your tv and then to your computer's RS232 serial (com) port via a null modem serial cable. Turned on your TV and your CW700 and set it to a channel which is an active nfps channel (300). Last step is to click once on the shortcut (icon) in the launch bar for rq-sssp-client.exe and you will get a black window with a blinking cursor on your screen. Within 1 1/2 to 2 minutes your TV should come alive with channel (300). Just to add, a lot of windows pc have the "Hide extensions" checked in folder options. If this is checked, the rq-sssp-client.conf.bak file will appear as rq-sssp-client.conf and the incorrect file would be edited. If one does not see the .conf.bak file then it is important to first go to Folder Options and then uncheck the "hide extensions" under the view tab and then edit the rq-sssp-client.conf file. |
|
Silver Member Username: Pirate_pete_208Post Number: 274 Registered: Jan-10 | Please, Nydass enough is enough already take a shower with Canada clean water |
|
Gold Member Username: Saqeeb9000Post Number: 7311 Registered: Oct-07 | if u like the service for free trials..send me pm..and i will provide u access code for $ 42..for a year.. |