no james...... what u need to do is go to menu , internet, then network information, find ur ip adress...... now write down ip adress at some paper.. now go to internet browser, in adress bar type ur ip adres. just like you type [link removed] [link removed] some hints .. when u are putting ip adress in adress bar, change the channel or some times tune in to 100 or 102 channels also help.. when u will type ur ip adress u wil get in to webloader, over there locate ur 1.47 bin that u saved and then clik on upload wait 1 min........ and ur rec will turn off and on again.. to check if u have latest bin, check under menu system setting, it should says 1.47.. after thaat if u still not up, go to menu usersetting and turn off emulator and autorolls on... this should work.....
hmmm, its asking for user name and password after i typed the receiver's IP address LOL....i left it all blank so i just pressed enter, just stalling now.... sux
Ok thanks the username and passowrd works....my next problem was after i press enter, it jus stalls or gives the internet explorer difficulties.....so i said forget doing it wirless
i went for the regular serial to serial cable from my laptop to receiver and it worked for that part !
just make sure you have the RIGHT CABLE, i had the wrong one....meaning i had the COOLSAAT female to female cable but that wont work on Nfusioon lol...u nneed another female to female cable, weird
i've been using this site to help me with things, least i can do for other novice users...
james singer. so what happend when u load the file......did u download it using webloader (the method i mentionded above)... try to do factory reset and try again.. will be easier.. what message are u getting?
Hi sada, i just did your method, and it's working, the thing is that i don't have Internet Support (says: Configuring Network Connection, and then Fail To Connect)
some suggestion for people whose webloader is not working.......
if u can not use ur microsoft internet explorer try mozilla fire fox..always works better for webloader... also when u are putting ip adress on ur adress bar when u hit enter, change the channelalways works.. 3rd method u can also download the channel editor program (1.10) from [link removed] and then use the program there to grab the bin, works faster... also if u are doing it withur laptop computer try to do it with (network cable).. better connection... last thing if u still can't do it do it old fashioned way..with serial cable check am's post above...
Sada. I appreciate your help as well as your patience. Since I was having diificulty uploading 1.47 I had a guy come over a program it for me. Everything is set but still nothing. I even rebooted the modem and router. Don't know what else to do
ok couple of things to check.. under menu, user settin , is ur emualtor off and autorolls on.. 2nd thing to check if u have latest file, menu under system setting should be bin 1.47 3rd.. how is ur internet connection setup. i believe withwireless router.. do u have a wireless laptop.. is ur router is working ok.. do u get red light on ur rec when u plug in ur network cable? i think there might be problem with ur wireless router try to change the network cable to port 2 or port 3 of ur wireless router..
"what is a message u are getting when u change the channels"?
did u also check under menu , installation, anteena setting? do u get green signals?
are u able to scan the channels.. go to menu, installation, under anteena setting ,what ever dish u currently have , change to ur diseqc mode to what ever port ... depends on setting.. u should be able to see green signal for signal and quality.............. for example.........
11 CHECK BOOT AND S/W VERSION Once you connect Nfusion to your TV, you should see MAIN MENU display on your TV screen. if not Press Menu on your remote Scroll down to System Settings then press OK Input your default password 0000 Scroll down to S/W Version then hit OK on your remote key. Now you should see new Boot and S/W You are successfully loaded software to your STB EMULATOR If you want to use IKS then it is very critical that you have to run EMULATOR = OFF. Emulator= off meaning your using IKS server which is your Nfusion required connect to internet while viewing TV. Emlator = ON meaning it is using stand alone bin. I would recommend you to use IKS that way you can avoid ECM. let the server do the hard work Menu->User Settings->Emulator Created by HumanNetwork [link removed] Rev 3 16 ANTENNA SETTING example if you have 2 dish..
110W and 119W stationary dish. in this example we going to use Single LNB type and DiCEqC 1.0/1.2. I assumed that your physical dish properly setup. if not please setup your dish before doing the following steps. STEP1: Press Menu key on your remote Press OK on your Remote control key STEP2: Input password 0000 0000 is the default password for nfusion Created by HumanNetwork [link removed] Rev 3 17 STEP3: Press OK on Antenna Setting STEP4: Satellite is highlight, Press OK on your remote control Created by HumanNetwork [link removed] Rev 3 18 STEP5: Press double arrow down key on your remote until you see 110.0W ECHOSTAR 8/1 then press OK on your remote control. LNB Type = 1. Standard LOFreq = 11250 22KHz = OFF DiSEqC Mode = Port 2 (I used port 2 for 110. set this according to your physical port setting.) Multi-Dish Switch = Disable Motor Settings = OFF LNB Power = ON you should see EchoStar 110 banner popup on your screen. S and Q also have green bar. S = Signal Q= Quality. we are not too concern about the Q. we more concern about S. The higher the S is better. if you own other STB you might see their signal better than NFusion, but I won't worry about it if I were you. as long as your dish setup properly. Created by HumanNetwork [link removed] Rev 3 19 STEP6: Now press Menu once on your remote control. STEP7: Press OK on your remote control to save. STEP8: Press OK on your remote control again to get back into Antenna Setting Created by HumanNetwork [link removed] Rev 3 20 STEP9: Scroll down to Search Channels CH All Search then press OK to search auto scan 110W. STB scanning the selected bird. sit back and watch the channels coming through Created by HumanNetwork [link removed] Rev 3 21 Once Auto Scan is done STB automatically update itself and it will automatically exit itself. Screen after scanned. Created by HumanNetwork [link removed] Rev 3 22 SETUP 119W Repeat the same process as 110W. The only difference is your PORT setting. Change the port setting to correspond with your physical setup. LNB Type = 1. Standard LOFreq = 11250 22KHz = OFF DiSEqC Mode = Port 3 (I used port 3 for 119. set this according to your physical port setting.) Multi-Dish Switch = Disable Motor Settings = OFF LNB Power = ON Created by HumanNetwork [link removed] Rev 3 23
I have loaded bin 1.47 on my Nfusion box and everything is up and running. However, some of the channels don't have audio although the picture is fine. Is anyone else experiencing this problem or does anyone know how to fix it?
