For lk or plymouth

 

Bronze Member
Username: Vicb

Post Number: 61
Registered: Jan-07
hey plymouth & lk . i have been having an auto toll problem since last week from before the emc. i tried everything new defaults, ect.. i took plymouths advise this am and deleted dn codes. good news is that yes the codes did roll back. but i still get ' auto roll processing" on the screen. dude all the channels are in as per evidence in guide. channel 100 shows pictures and sound of top 6 channels. but nada, nothing zippo. i turned the box off and have it on channel 122. and its been rolling for 10 minutes now.. my pansat recently died and i had this viewsat as a back up from last summers long emc.\
any suggestions??
 

Gold Member
Username: Kirankumar

NO Bashing

Post Number: 2718
Registered: Oct-07
please post your antenna settings
 

Platinum Member
Username: Nydas

Post Number: 10490
Registered: Jun-06
Just do:
1. Note down ALL antennas settings
2. Install factory BIN.
3. do a reset.
4. Install latest BIN
5. Set up one sat.
6. do a full scan (either Blind or similar).
7. Set up other sats.
8. do full scans.

Teh keys will roll in about 10-30 minutes.
 

Bronze Member
Username: Vicb

Post Number: 63
Registered: Jan-07
echo 7

lnb power on
lnb type standard
lnb freq 11250
22khz off
tp freq 12224
disceq port 2
motor off
legacy off

echo 8

all the same except for the diseq, which is port 3
 

Gold Member
Username: Kirankumar

NO Bashing

Post Number: 2719
Registered: Oct-07
which mode receiver do you have?
 

Platinum Member
Username: Nydas

Post Number: 10495
Registered: Jun-06
There is something slightly unusual about the settings posted above.
Echo 7 is usually at DisEqC port 1 and Echo 8,10 at Port 2.

If and when you do total reset as suggested above, you should remember to use these settings if your regular ones do not work. if fact, before you do a total reset, you might try these settings and rescan.
 

Platinum Member
Username: Lklives

Post Number: 15569
Registered: Jan-06
Did U try shutting OFF the autoroll feature in the receiver?

also, I don't know what LNB type U are using, so your antenna settings may be incorrect...

usually the 119 is on #1...and the 110 is on #2..especially if using Dish Pro hardware ..
 

Gold Member
Username: Kirankumar

NO Bashing

Post Number: 2720
Registered: Oct-07
which mode receiver do you have?
 

Platinum Member
Username: Nydas

Post Number: 10502
Registered: Jun-06
LK: Thanks for confirming the normal settings for Echo 7 and echo 8,10 - something that has been known for at least 2 years if not more.
Can you read the post just above yours?
 

Bronze Member
Username: Vicb

Post Number: 65
Registered: Jan-07
what is receiver mode african, and yes, i have always been set up with 2 & 3 on my diseq. remember, i had a pansat and all worked well. even my viewsat until last week..
 

Bronze Member
Username: Vicb

Post Number: 66
Registered: Jan-07
i am now working on nalin's advise. set up one antenna then scan. it seems to be taking longer to scan as when i scanned befor process complted very quickly. im am now settting up and scanning other antenna. will let u know..
 

Gold Member
Username: Kirankumar

NO Bashing

Post Number: 2722
Registered: Oct-07
sorry typo
i meant model and make of receiver
 

Platinum Member
Username: Nydas

Post Number: 10504
Registered: Jun-06
With some LNBs, the 119W scans with port 1 and the 110W scans sometimes with port setting "NONE" instead of 2.
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2170
Registered: Jan-08
Sorry i dont understand your problem slick
Explained me please
 

Gold Member
Username: Kirankumar

NO Bashing

Post Number: 2724
Registered: Oct-07
all he is getting is "auto roll"
 

Platinum Member
Username: Lklives

Post Number: 15573
Registered: Jan-06
slick...U are in serious trouble if ya listen to anything nalin says!..she has killed many peoples receivers here, giving out bogus info to many newbies...thats a known fact here by all of the regulars and old timers here..

good luck..don't complain when your receiver dies!...U were WARNED!
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2171
Registered: Jan-08
Slick
you need to delete provider not the keys inside
 

Platinum Member
Username: Nydas

Post Number: 10506
Registered: Jun-06
LK: Your tactic to keep a following including multiple names, scaring people posting large C/P are all exposed.
You are a redundant "have been there" FTA user, laid off by all the sites that have any sense and even not allowed to post there.

So buzz off, old woman, and let people help people here. We do not want another one of your scams like the ftaprosupport scam, where YOU were one of the principal players and beneficiary
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2172
Registered: Jan-08
Always scan sat one by one slick

Guys please dont affraid slick

Thanks
 

Bronze Member
Username: Vicb

Post Number: 67
Registered: Jan-07
nalin i do not get a signal or quality on port 1 only on ports 2 & 3 i am now switching ports to antennas and scanning to see if this wirks as i may have forgotten when i defaulted..

and plymouth dont worry i love you 2 :-)
 

Gold Member
Username: Kirankumar

NO Bashing

Post Number: 2725
Registered: Oct-07
try hooking up dish directly,bypass the switch with a coupler and if that solves the problem replace switch
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2174
Registered: Jan-08
African is right try without switch
 

Bronze Member
Username: Vicb

Post Number: 68
Registered: Jan-07
coupler?? meaning a regular cable 2 way??
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2175
Registered: Jan-08
Upload
 

Gold Member
Username: Kirankumar

NO Bashing

Post Number: 2726
Registered: Oct-07
look at the picture above
you hook up cable for dish to one end and cable from receiver to the other end,
this way you by pass the switch and if it works that means you have a bad switch and need to replace it
 

Bronze Member
Username: Vicb

Post Number: 69
Registered: Jan-07
nice picture plyjmouth lol
but what do i couple?? meaning i have 2 from the dish going to 1 my box?? so i couple the 2 comming out from the dish??
 

Gold Member
Username: Kirankumar

NO Bashing

Post Number: 2727
Registered: Oct-07
no just one and look at my post above
1 from dish and the other from receiver so you are getting a direct connection from dish to receiver for any one bird for testing purposes
 

Bronze Member
Username: Vicb

Post Number: 70
Registered: Jan-07
ahh gracias
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2176
Registered: Jan-08
Choose LNB for sat you want scan
 

Bronze Member
Username: Vicb

Post Number: 71
Registered: Jan-07
used coupler and still nothing nada.. this sucks. it was going on and off last week.. meaning rolling, then nothing. all ny signals and antennas are good chanels even scan in. as a matter of fact i get channel 100 9dish info) with 6 cahnnels all together all with picture and sound, but i leave it on 122 for a while, all day, and zippo
im at wits end muy fta brothers.. stummped
 

Gold Member
Username: Kirankumar

NO Bashing

Post Number: 2728
Registered: Oct-07
can you hit the SAT button on your remote and make sure it is on "all satellites"
 

Bronze Member
Username: Vicb

Post Number: 72
Registered: Jan-07
oh i though it needed to be echostar package?
 

Gold Member
Username: Kirankumar

NO Bashing

Post Number: 2729
Registered: Oct-07
change it to all satellites
 

Bronze Member
Username: Vicb

Post Number: 73
Registered: Jan-07
changed it & brother i get nothing.. gonna get my pansat j-taged. cauz i dont know what the deal is. the viewsat was working fine up til last week.
 

Gold Member
Username: Kirankumar

NO Bashing

Post Number: 2732
Registered: Oct-07
before you give up,do this,posted by Nalin
the only thing is do not do blind scan,do auto scan

Nalin Nyda
Platinum Member
Username: Nydas

Post Number: 10490
Registered: Jun-06

Posted on Monday, May 05, 2008 - 09:21 am: Edit Post
Just do:
1. Note down ALL antennas settings
2. Install factory BIN.
3. do a reset.
4. Install latest BIN
5. Set up one sat.
6. do a full scan (either Blind or similar).
7. Set up other sats.
8. do full scans.

Teh keys will roll in about 10-30 minutes.
 

Bronze Member
Username: Vicb

Post Number: 74
Registered: Jan-07
african should the tp auto roll be on or off???
 

Gold Member
Username: Kirankumar

NO Bashing

Post Number: 2733
Registered: Oct-07
on,
also get a fresh copy of the new bin from www.ftaforall.net
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2177
Registered: Jan-08
slick problem is on viewsat or pansat?
 

Bronze Member
Username: Vicb

Post Number: 75
Registered: Jan-07
viewsat platinum 2000
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2178
Registered: Jan-08
Ok you can try this:
try it:
All viewsat box
"Write your sat info before"
Go to Code menu
Select Nagra and on Dish 01 06 00 Dish 00 01 00 dish 01 01 00
Delete this 3 provider one by one with F3 on remote
"NEW" do same thing with all provider on Bev provider
09 07 00
09 06 00
09 05 00
09 01 00
08 01 00
no need to delete keys
switch off 10 secs on back panel
and load last bin for your box
turn autoroll on
Keep on
Bin and autoroll regenerete keys
Resolve problem with lost channel , autoroll, freeze and search signal


Do setup on each sat and auto scan on each sat after for recover all channel
"Dont do a blind no need"
"Dont load factory bin"

Thats erase bad data in the box
For box who lost channel and sat setup
ENJOY TV

TESTED and work fine
New issue for problem on Viewsat
Thanks

Reply if it work
Please
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2179
Registered: Jan-08
Do exactly as write
 

Bronze Member
Username: Vicb

Post Number: 76
Registered: Jan-07
ok i am trying nalins way now..with the factory bin procedure.. will let u know
 

New member
Username: Lly

Post Number: 1
Registered: May-08
Did tou try loading the latest bin that came out yesterday morning?
 

Bronze Member
Username: Vicb

Post Number: 77
Registered: Jan-07
plymouth i tried it your was this morning. i have now been trying everything since 8 am this morning.
waitng for autoroll now after complete factory reboot and file lets see.
but i do greatly appreciate all your help african, nalin & lk :-)
 

Bronze Member
Username: Vicb

Post Number: 78
Registered: Jan-07
15 minutes and still rolling
kawabunga @!@!@!
 

New member
Username: Lly

Post Number: 2
Registered: May-08
Did you try the new file? Not just the factory file.
 

Gold Member
Username: Kirankumar

NO Bashing

Post Number: 2734
Registered: Oct-07
if you ave a platinum make sure you are using this file

http://ftaforall.net/forums/showthread.php?t=34800
 

Bronze Member
Username: Vicb

Post Number: 79
Registered: Jan-07
of course i have the right file lol
this started happening last week with the old bin , but before the emc.
im at wits end. im just letting it auto roll since i did a factory reboot it been 40 minutes now and nada. this sucks.
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2180
Registered: Jan-08
Slick where you take your bin?

Dont install factory bin
 

Bronze Member
Username: Vicb

Post Number: 80
Registered: Jan-07
nothing still rolling same old sh_t @!@!
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2181
Registered: Jan-08
Where you take your bin?
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2182
Registered: Jan-08
Allo! where you take your bin?
 

Bronze Member
Username: Vicb

Post Number: 81
Registered: Jan-07
at freedomfta
ive always gotten my bins there. thrust me its NOT the bin dude
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2183
Registered: Jan-08
try the bin LK post:
https://www.ecoustics.com/electronics/forum/home-video/480400.html
 

Bronze Member
Username: Vicb

Post Number: 83
Registered: Jan-07
why would i pay for something that is free.. lk can bite me
its NOT the bin for the millionth time
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2188
Registered: Jan-08
Sorry i dont check the link
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2189
Registered: Jan-08
OUPPS
 

Platinum Member
Username: Lklives

Post Number: 15579
Registered: Jan-06
hey slick dik...fock U pal..i hope ya never get that focker working!

I posted FREE files HERE for everybody to use...so go suck my KOCK if ya don't like it!...U STUPID muther focker!

Anybody here who helps U after U bashing me like that, can all go to hell too!

I will NEVER post FILES here again!...I'm tired of azzholes like slick dik, and people who support and help those azzholes!


BTW, if ya don't know why I'm pissed read slick' post a few up, and what he said to me and my files!..and fock U too, if ya think I'll accept any apology either!...FOCK YOU!
 

Gold Member
Username: Donnie1973

Post Number: 2971
Registered: May-06
slick, u REALLY need to change ur disecq settings to echo 7=1 echo 8=2
I have seen this exact problem and that is the solution. Change it on the disecq switch AND the ant settings. I suggested this last week. If it hasnt worked in two weeks I would try EVERYTHING people tell me. Good luck.
 

Gold Member
Username: Donnie1973

Post Number: 2972
Registered: May-06
and slick, u WILL not get signal on echo 7 disecq port 1 unless u change the TP to 12239. This is an EASY FIX. Do as I suggested last week. U are basicly setting up the same sat twice. An just because u may have to register at a site doesnt mean u have to pay. U should be grateful to be getting this much help for such a stupid easy problem
 

Gold Member
Username: Donnie1973

Post Number: 2973
Registered: May-06
sry LK, i have been seeing everyone here helping him for 2 weeks, I know the problem and would like to quit reading posts about this same problem
 

New member
Username: Lly

Post Number: 3
Registered: May-08
Amen!
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2190
Registered: Jan-08
danten
he want help but dont try what we say
 

Gold Member
Username: Donnie1973

Post Number: 2977
Registered: May-06
the great nalin the platinum member shoulda known what I told him, but I figured she wouldnt know something so... well, it was painfully obvious to someone who has set up a few before. Unlike Nalin. Once again, she offers no help to the members here, she tried, but its hard to help someone when u dont know what ur doing.
 

Bronze Member
Username: Lklies

Post Number: 86
Registered: May-08
dantetn..... Nalin had given same advice, U know.....
 

Gold Member
Username: Donnie1973

Post Number: 2994
Registered: May-06
nalin had said he thought they should be the way i said, then after slick said his pansat worked on it and he wasnt getting quality on disecq 1 is the biggest give away of his problem. Its things like that u/I would expect from someone who is a platinum member, and always says he knows more than most will ever learn. LMAO.
no one sees slick asking for help anymore eh???
 

Silver Member
Username: Luser

Post Number: 256
Registered: Nov-07
Everyone listen up. Slow down. A mechanic says maybe this try that. A trouble shooter will eliminate possible errors by deduction. Now it seems clear that perp has switch not realizing settings of port1 for 119 refer to the built in lnb switch and that one wire is all thats needed and port2 set to 110. Dont use 4port switch for now. It also sounds like by the time he gets it working the bin has expired. The file name is the date released. Use that date to verify when saying "I know its not the bin". Lets all slow down and try to troubleshoot not mechanic.
 

Platinum Member
Username: Nydas

Post Number: 10516
Registered: Jun-06
dantetn said: "u WILL not get signal on echo 7 disecq port 1 unless u change the TP to 12239. "

Here is what lyngsat says about the first and 2nd TP of Echo 7.

http://www.lyngsat*com/packages/dish119.html

12224 V tp 1 SR 20000 FEC 5/6

12239 H tp 2 SR 20000 FEC 5/6

And 12224 does work as stated - that you can have just one TP the first one and all will be scanned.
Also I had told this guy to use Blind scan, and it would have worked.

I know exactly why Echo 7/TP 12224 works in some situation and in some it does not work. Now go to your Mummy LK and ask her why.
 

Silver Member
Username: Gregraf

Post Number: 481
Registered: Dec-07
Nalin Nyda is a LOSER
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2237
Registered: Jan-08
Guys Tp freq it just for see if you have good satellite, try with other Tp freq an do a scan an that work well
LNB freq is very important and you must have good one.

Test and see

Thanks
 

Gold Member
Username: Donnie1973

Post Number: 2996
Registered: May-06
ok sweetheart, u try it urself... dont go read and test the THEORY of testing. TEST. With 119=disecq 1 ans 110=2, look at the quality on 119 tp 12224 (default tp) do u have quality? NO. UNLESS... ur disecq settings are wrong. 99% of the time with those symptoms THAT is the problem, as I said. I am done with u.
As king would say, if yo listen yo may learn something. lol
 

Gold Member
Username: Donnie1973

Post Number: 2997
Registered: May-06
And, it would NOT have worked if he did a blind scan. Try that to dear. If ur disecq settings are wrong, it will conflict each other. Quit trying to prove u are litterate and test it urself and please report the findings.
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2240
Registered: Jan-08
OH OH dantetn take it easy i dont attack you.
First i have a universal invacom LNB( only one LNB)and dish with motor.
With it i scan 15 satellites on linear and cicular signal.

I agree with you for this NO. UNLESS... ur disecq settings are wrong. 99% of the time with those symptoms THAT is the problem, as I said

I presumed this guy try to set diseq switch.

Thanks
 

Gold Member
Username: Donnie1973

Post Number: 2998
Registered: May-06
no no ply, those posts were for nalin.
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2242
Registered: Jan-08
OK
 

Platinum Member
Username: Nydas

Post Number: 10519
Registered: Jun-06
Dantetn:
http://www.lyngsat*com/packages/dish119.html

12224 V tp 1 SR 20000 FEC 5/6

I know exactly why Echo 7/TP 12224 works in some situation and in some it does not work. Now go to your Mummy LK and ask her why.
 

Gold Member
Username: Donnie1973

Post Number: 2999
Registered: May-06
as i said before sweetie, im not interested in the THEORY, just what the end user sees. I know u arent a real tester, u just play one on ecoustics.
or did u sleep at a holiday inn expess last night.
U should learn what u are telling people before u try to help them. This is why u have destroyed many recievers on here. Dont u have to get up early for school in the AM? Its goota be past ur bedtime.
 

Platinum Member
Username: Nydas

Post Number: 10521
Registered: Jun-06
dantetn: It is NOT theory, you blind skunk.
I specifically said that
TP1 12224 V setting for Echo 7
works for some and does not work for others. A very reputable and much consulted site called Lyngsat says it it is the first TP for 119W (Echo 7). There is a specific reason for it.
You had the audacity to try and ridicule and contradict me about it.
NOW ASK YOUR MAMA LK WHY

AND LEARN FROM THE OLD WOMAN;

OTHERWISE SHUT UP.
 

Gold Member
Username: Plymouth

Quebec city, Quebec Canada

Post Number: 2250
Registered: Jan-08
dantetn Nalin is right

Transponder beam can changed, it depend where you are(east or west)

Nalin take it easy, you can reply without it:
"You had the audacity to try and ridicule and contradict me about it.
NOW ASK YOUR MAMA LK WHY

AND LEARN FROM THE OLD WOMAN;

OTHERWISE SHUT UP.
" please.

Thanks
 

Platinum Member
Username: Nydas

Post Number: 10524
Registered: Jun-06
dantetn had better reply. He has been inturrupting me for th epast one year - always with a ridicule and he pretend to know a lot. In this thread I was the first one to point out at:

May 05, 2008 - 09:37 am:
Echo 7 is usually at DisEqC port 1 and Echo 8,10 at Port 2.
Dantetn at:
May 05, 2008 - 05:47 pm:
and slick, u WILL not get signal on echo 7 disecq port 1 unless u change the TP to 12239.
Dantetn at:
May 06, 2008 - 10:58 pm:
119=disecq 1 ans 110=2, look at the quality on 119 tp 12224 (default tp)

All this time I had not suggested to anybody to use TP freq of 12224 for 119W. My normal recommendation is to use 12224 V for Echo 7 if it will work otherwise use 12239 H, so what the hell is he doing ridiculing me?

There is a reason for this duality of success/failure which this blind skunk called Dantetn does not know and refuses to acknowkedge.
He goes on attributing something to me I never said.
 

Gold Member
Username: Donnie1973

Post Number: 3002
Registered: May-06
u did say exactly what u wrote above in the 6th post in this thread. THE 6TH POST!! His problems remained! I just guess people needing help look to a "platinum" member to get help. U ARE NO HELP TO ANYONE HERE UNLESS THEY NEED TO CONVERT THEIR RECIEVER!!! PERIOD!!!
U are right, I had no idea about east and west picking up 12224 on 119. None. I actually know what a reciever will do under different settings, BECAUSE I TEST IT. U dont see him needing more help do u? And all from a lowly "gold" member.
Nalin, u need to stick with the converts. As u should know something about.
 

Silver Member
Username: Pulpfiktion

Post Number: 221
Registered: Mar-08
Dantetn....U R an idiot and dont now a thing.

Stop bragging....
 

Silver Member
Username: Pulpfiktion

Post Number: 222
Registered: Mar-08
Hey Idiot Dantetn....
Read what slick say.

U did not help help him....
« Previous Thread Next Thread »



Main Forums

Today's Posts

Forum Help

Follow Us