Installed New ViewSatFile but not getting enough channels

 

Bronze Member
Username: Reach_honey

Post Number: 59
Registered: Mar-05
I have loaded this new file and all channels are working.I'm getting all channels from 148 and 110 angles. But I'm not getting any channels from 119.
Below are my setting for VIEWSAT ULTRA(WITH USB)
Satellite: Echostar 1,2(148)
LNB: on
LNB type: Standard
22KZ: OFF
LNB FREQ:11250
TP:12224
PORT:3
DISEQC: NONE
MOTOR:-OFF
SET LEGAcy OFF
-----------------
Satellite: Echostar 8,10(110)
LNB: on
LNB type: Standard
22KZ: OFF
LNB FREQ:11250
TP:12224
PORT:2
DISEQC: NONE
MOTOR:-OFF
SET LEGAcy OFF
-------------------

This is where it is creating a problem.It does not change and it shows as echostart(8,10) on side.
Satellite: Echostar 7(119)
LNB: on
LNB type: Standard
22KZ: OFF
LNB FREQ:11250
TP:12239
PORT:2
DISEQC: NONE
MOTOR:-OFF
SET LEGAcy OFF


-------
I have subscribed to DISH legally and they have installed 2 DISHes.
One dish as dual LNB which is used for 110 and 119 and other dish has dual LNB (But only one is used) for 148.
One cable goes from one dish to other one and from both one cable comes out and goes into a Switch which eventuallu brings out one cable which goes into my DISH Receiver.

I used that cable to have input into VIEWSAT ultra.
So please let meknow how can I see all channels.
Thanks,
 

Silver Member
Username: Dimwitt

Post Number: 226
Registered: Aug-06
change port on echo 7 to 1
 

Bronze Member
Username: Tvhammer

Post Number: 16
Registered: Nov-07
getdss.com
 

Silver Member
Username: Bill038

Post Number: 181
Registered: Sep-06
John the spammer,,,,you suck
 

Bronze Member
Username: Reach_honey

Post Number: 60
Registered: Mar-05
John sucks big time.
For echo 7 I have changed port to 1 and it does not show any Quality Strength.If I changed it toPort 2 then it shows as echo 8,10 instead of echo 7 and so when you do blind scan you get channels repeat for echo 8,10.
 

Bronze Member
Username: Reach_honey

Post Number: 62
Registered: Mar-05
Any one with any ideas....
 

Bronze Member
Username: Chrisduclo

Post Number: 98
Registered: Aug-06
you may have a bad lnb, which was my problem. a new dual lnb was my solution. on the dishpro lnbs the setting for echo 7 is always 1...my only solution is to try port2 and diseqc 1 for echo7 .... on my pansat2700 there are no port settings but i use diseqc 1 for echo7 and diseqc 2 for echo8. good luck
 

New member
Username: Tin42man

Post Number: 1
Registered: Nov-07
put 119 on port 1 and use tp 2 as tp 1 has no channels and will not show a signal for 119
 

Bronze Member
Username: Reach_honey

Post Number: 63
Registered: Mar-05
Chris,
As I said I'm getting all channels from regular DISH receiver. So I don't thing there will be any problem regarding LNB's.

Tinman,
I will try Port 1 for 119.
What do u mean by tp2 as tp1.
Can you please explain?
 

Silver Member
Username: Ke5aqn

IF I DONT KNOW THE ANSWER, I WILL FIND...

Post Number: 908
Registered: Sep-06
is it a dish 500?
 

Silver Member
Username: Timscarlet

Usa

Post Number: 267
Registered: Feb-05
hello, some tp's will not show a signal after you have switched to the port 1 for 119.
so try looking to see if the other tp's especially the 12224 that does not have sometimes a signal.
« Previous Thread Next Thread »



Main Forums

Today's Posts

Forum Help

Follow Us