Pansat3500 wont reboot

 

Bronze Member
Username: Droy1

Huntington beach, Ca Orange

Post Number: 15
Registered: May-06
lost keys and added what i thought was new bin but same old one but the box never flashed and is stuck there any help out there?
 

Gold Member
Username: Nydas

Post Number: 2801
Registered: Jun-06
Darren: For Pansat 3500 you need to change the Boot to B80 and then install new BIN. You may need to instal factory BIN first.
http://www.dssrookie.com
http://www.dssevolution.com

Some people are finding that the keys did not autoroll properly. There have been three key changes in the last two days on DN. Try turning off autoroll and manual update of latest keys for provider ID 0101.
 

Bronze Member
Username: Droy1

Huntington beach, Ca Orange

Post Number: 16
Registered: May-06
nalin thx but i have the b80inthere and when i turn onthe box its just setting there with the b-80 showing but not turning on
 

New member
Username: Sobe1

South beach, Fl

Post Number: 2
Registered: Jun-07
doing a factory reset and then load the bin again. some times this procedure helps.
 

Bronze Member
Username: Droy1

Huntington beach, Ca Orange

Post Number: 17
Registered: May-06
sobe i get no pitcher on the tv its like in limbo
i cant get into any menu screen because its blank
help
 

Bronze Member
Username: Gastrognome

Post Number: 36
Registered: Dec-06
I would load the latest bin when at b-80.
this site has info for you,
www.pansatusa.com/qna.html
 

Silver Member
Username: Hardrockstriker

Post Number: 887
Registered: Apr-06
if your loader can't communicate with your receiver then you'll have to jtag the unit.

you can do a search on this forum for info on how to jtag.
 

Bronze Member
Username: Droy1

Huntington beach, Ca Orange

Post Number: 18
Registered: May-06
thx to all for the help! at the pansat site there is q&a that answer all and instructed me what to due. im now scan for channels. once again thanks
 

Gold Member
Username: Lklives

Post Number: 9888
Registered: Jan-06
Question #2

I have a Pansat 3500S/SD (b-80) model which displays a "b-80" message on the front LED screen and the SD memory card function is not accessible. The television screen is blank and there is no menu displayed. What can I do to repair the receiver?

Answer: This situation can occur when the receiver's direct power source is interrupted before download is complete. The "b-80" message signifies that the receiver has lost all of its saved memory data. Do not panic. The receiver's memory can be restored to its normal condition by downloading software from your computer to the receiver. You can use the boot method download from your computer by using a null modem data cable connected to the receiver. After you connect the receiver to your computer, use one of the following two methods:

1. Turn the receiver's main power off (use reset switch on back panel). Open the GTRom Loader v35.01 (Pansat 3500S). Check www.pansatusa.com download section 3500S/SD(b-80) software to get V35.01 GTRom Loader. Next, open the bin file (The file should be dated Dec 17, 2006 or after ) to download. First, mouse click on the download then immediately turn the receiver power on. A dot on the receiver's LED display will move left to right while the computer counts down from 1-100%. If successful, a "ON" or channel number will appear on the receiver's LED display. If the download has failed, the "b-80" message will appear again on the LED display and the computer will read that the action has failed. Try this method again or use method #2.

2. Turn the receiver's power off and then back on. As soon as the "b-80" message appears on the front LED display, click download on the GTRom Loader v35.01 with your computer.
« Previous Thread Next Thread »



Main Forums

Today's Posts

Forum Help

Follow Us