ok i loaded the cw v 1.05 loader on to my computer and connected the null modem to com port1. but when i try to load it to my box it wont allow me to. on these directions i have it states that you must load "CX_KroundV1.06.bin and CX-LoaderV2.50.bin" as well are these seperate bins or am i not doing it right?
U really should go to www.future-fta.info/forums and read and post there in their DEDICATED Captive Works section...yes, U must register there for free..
The following does not apply to the Captive Works Premium reciever.
The new CaptiveWorks 600s REGULAR reciever comes loaded from the factory with the Kround OSD. If you just got a new one, these are the instructions. (If it is old, you may have to reffer to these instructions, and ask someone in the forums for some help:http://www.future-fta.info/Forums/sh...d.php?t=20290)
1. Get the current 1.05 loader here: http://www.future-fta.info/Forums/sh...ad.php?t=20296
2. Download the latest bin from here (top bin; highest bin number): http://www.future-fta.info/Forums/fo...play.php?f=176
3. Load the latest bin (from above) with the current loader (from above) as per these instructions:
Open 1.05 loader, select the latest bin in the "File" bar across the top. For Options, select Download S/W. For Select a port, choose your COM port (usually 1).
Prepare reciever: Turn off and attach the null-modem cable between the reciever and the computer serial port. Turn back on. With the CaptiveWorks 600s REGULAR reciever on, press the front power button and hold it. While holding it, turn off rear toggle switch, then turn on again while STILL holding front power button. You will see "boot" on the front display. At this point, remove your finger from the front power button and press "start" on the 1.05 loader. Wait for the reciever to display "-end". At this point, turn reciever off at rear switch, and then turn on again.
4. Perform Factory Default: Using Remote, press: Menu, Installation, Factory Default, All, ok, yes, ok.
5. Setup the reciever:
Select language Select GMT time (-5.00 is Eastern), summer off in winter. Search channel
Set DiSEqC switch ports and scan. Upon completion, press F1 key (you will notice an "h" on the front panel display), and "000" to enable the patch. (repeat with "555" to enable cardshare). Allow time for keys to roll.
Setup up OSD options:
Menu System Settings System Channel NO. - SID Key Update Message - Off B**andD**hnet Full Name - ON
Menu System Settings OSD Auto Exit Channel List - YES Channel List - CH 10 (appears when you press OK button, lists 10 channels, or 24)
Now, you don't have to select these options, but I do recommend them. Thanks to the other Mods who contributed to this thread. For more info regarding the Captive Works 600s Regular/Normal (not premium) reciever, visit our stickies: http://203.169.142.72/~future/Forums...play.php?f=172
another non reading, non listening newbie..U better hope bruce will hold your hand here, cause i won't...I already told u the best place to go for help and info..U don't want to read and listen, then U pay the consequences...but don't trash up these forums witha million posts that could be answered in 10 minutes of reading somewhere else..
kewl ive been reading just not hard enough i guess? thanks for the support!! plus if you dont want to help, why bother opening the thread?? just a question i didnt put it out specifically for bruce or lk!
you ask last week and i did not have problum with helping and i no you did not go to the site i gave you or you would not ask how to get in to the site so if you read then whatdid you read if you cant get in the site today ? and i like helping others how like to help them seleves not ask the same question week after week and last week i did give you all theinfo on the cw600s
