Fta News This list will be updated as fixes are posted.
Working: Viewsat Xtreme [cardless] Auto roll Works Working: Viewsat 2000/Platinum/Lite [cardless]Auto roll Works Working: Viewsat PVR7000 [cardless] Working: Sonicview PVR1000 [cardless] Working: Sonicview SV-1000 [cardless]Auto roll Works Working: Cool*sat 4000 [cardless] Working: Cool*sat 5000 [cardless]Auto roll Works Working: Cool*sat 6000 [cardless]Auto roll Works Working: Pansat 6000 [cardless] Working: Pansat 5000 [cardless]Auto roll Works Working: Pansat 3500 [cardless]Auto roll Works Working: Pansat 2700 [cardless]Auto roll Works Working: Pansat 1500 [cardless] Working: Pansat 2300 [cardless] Working: Pansat 2500 [cardless]Auto roll Works Working: Ariza 800 [cardless] Working: Ariza 750 [cardless] Working: Ariza 700 [cardless] Working: Pansat 2700A/E [cardless] Working: ExtremeView Magnum XV3300 [cardless]Auto roll Works Working: Captiveworks CW-600S [cardless]Auto roll Works Working: Captiveworks CW-600 Premium [cardless]Auto roll Works Working: Captiveworks CW-1000S [cardless]Auto roll Works Working: Buzz S2010F [cardless]Auto roll Works Working: Buzz S2010F Plus [cardless]Auto roll Works Working: Fortec Ultra/Pantec Pansat Clone [cardless]
NOTICE for Viewsat users: When finished it will say END, then 00.00, then boot, then END, then back to last channel or 00.00. You must wait until this process finishes before unplugging.
FTA fixes such as Card/Internet sharing or "aux" card and others listed below.
Working: Dreambox (w/ Rom102/blocker or "auxed" card sharing) Working: Neosat iPro 1000 (w/ Internet Key Sharing - IKS)
Fta Keys DISHNET Status:
Dish has begun morphing keys. This may only effect some channels on Dish at this time, but has effected most on the *other. There is a new B1 routine that is similar to fake keys. For FTA, manually entering keys and turning auto-roll off will get you back up and running. They are disabling autoroll by morphing the 12th byte, there is no fake keys being sent. They are however checking for autoroll routines. The B1 they are using is effecting all forms of testing. It is unknown whether new bins will be released to address this at this time. Remember...Shut off autoroll and put in today's keys. If it goes black again...check for newer keys to manually enter.
Current DISH Network NagraVision 2 Keys
Dish Keys 00 (86): 2F 64 46 8B 3D F3 27 DA 59 A3 31 51 F2 F2 24 34
00: 2F 64 46 8B 3D F3 27 DA
01: 59 A3 31 51 F2 F2 24 34
ACTIVE Dish Keys 01 (96): 17 99 73 9F 04 B7 F0 2A AD 02 51 13 67 5C 6E 4A
00: 17 99 73 9F 04 B7 F0 2A
01: AD 02 51 13 67 5C 6E 4A
***************************************
Dishnet & other providers can swap back and forth from one key to the other. If one does not work...try the other
Dish & other providers CAN also, and sometimes WILL run both keys active where some channels such as po*rn would work with one key, and the other channels with the other active key
• Most FTA's use the old N1 key spots in firmware, So they split the 16 byte key into two 8 byte keys. • These aren't accurate as Key00 and Key01 but rather are half's of the active key • Your more current stb flashes will support both keys for each provider now. Thank you from [link removed] Copy and Paste
Pluto. You are a new memeber. The keys are are in two groups of 8 numbers. I have separated the two groups so as to not post them on separate lines. Whne you come to DB, you pause and go to the next line. Same after 96. So stop your comments and start learning.