|
Silver Member Username: Nick32058Asdfvafdsv, QC Sdv Post Number: 113 Registered: Mar-06 | Before you start, set your reciever to factory settings. 1. Connect your Pansat2500a clone to your computer via serial cable (straight). 2. Turn on your computer and unzip the files that you have first BL loader and than the bin file. 3. Turn on your reciever (the back button) wait for 20 seconds until it turnes on . 4. Run BL Loader. 5. Choose Com 1 in Com settings window. 6. Load the bin file that you have in to the window below (the file must be unzipped) 7. Select bin (not boot) 8. Hit Write bin Button and wait until it is finished than hit ok and exit. (do not turn off your reciever untill you see the window (completed)). 9. Turn off your reciever and disconnect from a computer. 10.Go and connect everything with your TV and turn the reciever on. 11.Fallow the installation to set up your antena Choose the right sats (8.10ku or 8.6ku, 7ku,for dish net or Nimik1.ku for bell) check if your (diseq) is set the right way. (instuctions are in Antenna Setup ) Do a blind scan for the sat you have selected if youare usinging more than one sat you have to scan all of them one after another.( instructions in Blind Scan.) 12. Go fix yourself a sandwich wile you wait for scans to finish. 13. Come back go to parental control and set defolt keys. 14. If you are using bell you'll have to enter the keys manually. (insructions are in Entering keys ) Antenna Setup: How to set up your recivers Antennas (dishes(LNBs). If needed choose language (in case if your reiciever was set to 'Factory settings' If not press menu button on you remote control 1. Select Installation and press ok 2. Select Antenna Setup and press ok (The screen will appear displaying a list of sattelites on the left and parameters of a sat. on the right.) 3.Select the name of sat. on the left of the screen and press ok (Dish Network sats are ' Echo 8.6ku and Echo 7ku) (Bell Express Vu sat is Nimik1.ku) Now if you are using just one dish (LNB) you do not have to change anything. AS long as you have good quality and signal (If not try switching diseqc parameters with 'vol button' of your remote control untill you find a signal) press exit . But if you are using multiple dishes(LNBs) you need to have 'Diseq switch' Diseqc Switch is a small box usually has 4 ports named 1,2,3,4 and one more port that connects it to your reciever. All your dishes(LNBs) have to be connected to this Diseqc switch. Ex. If one of your dish(LNB) is pointed to recieve Ecko 8.6ku and it is connected to a Diseqc switch box port #1 than, Select Echo 8.6ku on the left of the screen and press ok, now look on the right side of your screen. Go down to select diseqc function.(diseq parameters are "off, 1, 2, 3, 4.) Press 'vol button' on your remote control and set parameter 1. press exit. Your Dish is set and ready for scan. (Add another Dish) If your other dish(LNB)is pointed to recieve Eko 7ku and it is connected to a Diseqc switch box port #2 than, Select Echo 7ku on the left of the screen and press ok, now look on the right side of your screen. Go down to select diseqc function. Press 'vol button' on your remote control and set parameter 2. press exit. Now you have 2 dished ready for scan. If you have more Dishes(LNBs) connected to your Diseqc switch to ports 3,4. you have to do the same with every one of them( select them and select the right diseqc parameter). Blind scan: How to do a blind scan Befor you do a blind scan you need to upload the latest bin File in to your reviever. (instructions are in Step by step doc.) And set up your Dishes(LNBs) (instructions are in Antenna Setup.doc) If you have compleated the step by step and Antenna setup Steps You are now ready to proceede with blind scan. 1.Press menu on your remote control. 2.Select Installation and press ok. 3.Select Blind scan and press ok. 4.Select Sattelite (use your 'vol button' to select the sat you want to scan) 4.go down and select scan-all and press ok 5.Let it finish scanning and press exit several times. If you have more than one dish(LNB) you have to scan all of them. Entering keys: Entering Keys Pansat2500a clone 1.Press menu Button on your remote control. 2.Select Parental control and press ok 3.Select second pin and enter "0000" 4.Select nagravision2 and press ok 5.Select provider ID ( 0101 is for Dish Network ) (0901 is for Bell Ex Vu) 6.Select key Number Each provider has 2 key numbers(00 and01) Use the'vol button' of your remote to select desired key number Set 00 than. 7.Select Key Data first line and enter the first 16 digits of the key labeled 00. 8.Select Key Data second line and enter the last 16 digits of the key labeled 00. 9.Press ok to save. 10.Go back to Key number window and set key number to 01. 11.Select Key Data first line and enter the first 16 digits of the key labeled 01. 12.Select Key Data second line and enter the last 16 digits of the key labeled 01. 13.Press ok to save. Exit. Keys change constantly alway check for new keys on the net. Bell express vu keys D1 15 0C 8E 66 82 D9 80 90 A9 20 20 37 07 87 08 0C B7 0A F9 50 75 F3 5B 31 EC 79 97 5C D7 CE 1A |
|
Silver Member Username: Nick32058Asdfvafdsv, QC Sdv Post Number: 120 Registered: Mar-06 | Pnsat2500a clone users read this it will help you to win your batle for free TV |
|
New member Username: Felipe604El paso, Texas United states Post Number: 1 Registered: Jun-06 | hey nick i need the loader and bins email alicias604@aol.com |
|
New member Username: NynydrePost Number: 3 Registered: May-06 | hey nick i need the loader,the bin and simplfied instructions. I have a rs-232c cable (female db9 to female db9). JOSM234@YAHOO.COM |
|
Silver Member Username: EvadelparaisoPuerto Rico Post Number: 960 Registered: May-06 | andre your cable is for pansat 2500 not 2700, if you have 2500 you goes in the right ways. In the meantime go to dss**tester.com Pansat download area, download the last bin, in search write loader, and download the gt or bl loader, and you can simply the instrucction posted above. Enjoy |
|
New member Username: MinPost Number: 9 Registered: Jun-06 | I use the usb pda/serial adapter driver and the null modem cable for my 3500sd , when i try to download it always say flast fail or write fail . did i using the right cable ? |
|
Silver Member Username: EvadelparaisoPuerto Rico Post Number: 966 Registered: May-06 | Pansat 3500-Null But there is a nice way to set your receiver without cables, flashing the sd and download the bin rename and place the bin file in your sd code area. And i mean you cant use usb, only pansat 5000 do not have problems using usb. Im already posted all the instrucction how to set in 3500 with sd. |
|
New member Username: BanejPost Number: 1 Registered: Jun-06 | I have a cloned Pansat 2500A,now i have two bins in my receiver one for dish (bin274)which is not working but i will put 277 and another bin for globecast sat. Now when i write new bins for these two satellites do i just do it through BU 1.4 or do i need another program. Do i also have to erase the old bins or just keep writing new ones over and over? PLEASE HELP!!! THANKS |
|
New member Username: HouhouPost Number: 9 Registered: Jun-06 | Nick for pansat 2500a should i use the same clone ? or there is another file for that reciever. Thanks |
|
Gold Member Username: EvadelparaisoPuerto Rico Post Number: 1029 Registered: May-06 | hou: go to dss**tester.com search in pansat area safe bin for 2500 clone Pansat Files » X85BL CLONE SAFE for 2500's by Chancysand (June-10-2006) Finally here it is, the clone safe bin for all 2500 clones!!!!!!! By the one and only Chancysand! |