Need to know how to split signal for two receivers
crowfordy
Unregistered guest
Posted on
i have dish network, and i want to somehow split the signal so that it goes to two separate receivers. Can someone please tell me how to do this. thank you.
crowfordy
Unregistered guest
Posted on
i have a thing called a switch, and it looks like a splitter. On one side it has two two connections that are labeled lnb and on the the other side there are three connections. On this side all connections are labeled lnb except for the middle one that is labeled receiver. Can I use this thing for what I need, and if i can, how would i use it?
Hey crowfordy; IM a noob, but if I copy U, all U need is a simple splitter(1 in/2 out)make sure the frequency handled by the sw. is correct. U might try the sw. U have, using 2 of the inputs and the out,to receiver, give it a shot, after all this is called "testing", not signal theft. LOL!!!
Grimreeper
Unregistered guest
Posted on
you need a dp34 switch wich from the sounds you might have.do a search for dp34 switch you should find what ya need
If U only have 1 receiver, U can use a simple "splitter " to run to 2 TV's..otherwise "splitters" are NO good for anything!
U described a 4x1 disque switch...4 inputs LNB and 1 receiver..well that doesn't work for 2 receivers..
U don't say how many and what type (single, dual, twin, quad, Dish Pro, Legacy) LNB's U have or are using at dish, so we cannot give U an answer..
U need the right combo of LNB's and switches.
This document is directed to novice,and slightly experienced hobbyists.Its purpose is to help those in need of answers to basic switching setups;It is not directed to those involving 2 or3 types of LNB's to 5 receivers...you should already be blueprinted.
You must determine your setup and gear.Here we will try to get you started with the most efficient and reliable switches.
One LNB to one receiver..............no switch needed One LNB to two receivers...............no switch needed(requires a DUAL output LNB) Two LNB's to one receiver............This can be done with any one of the following; AB switch/2x1 diseqc/4x1 diseqc/22Khz switch/4x4 multiswitch
(1) A/B switch from wallyworld or Ratshack;works great,switches every time...you will need 2 cables run to switch. (2) 2x1 diseqc switch;works reasonably well;antennae settings must coincide with switch inputs. (3) 4x1 diseqc switch;Probably the most widely spread and unreliable switch on the market.Performance level is abysmal.Does NOT like 2 different types of LNB,long cable runs,water,humidity,or anything else.Best brand by far for a good price is Chieta,and Spaun for high end...better be for the money. (4) 22Khz switch; Very reliable tone switch.Easily installed and reasonably priced.One line from each LNB to switch,and one line out to receiver.Highly recommended. (5) 4x4 multiswitch; Very versatile switch that requires dual LNB's.It can drive up to 4 receivers,and is 22Khz operated as well.These were around in the old D*V days and have an excellent track record and are highly recommended.
Two LNB's to two receivers..........This is where multiple switches is required in 3 of 4 examples.
(1) 2x1 diseqc switch;2 required for this installation,as well as 2 dual LNB's.The outputs from each LNB will go to a separate 2x1 switch,and from switch to receiver. (2) 4x1 diseqc switch;2 required for this installation,as well as 2 dual LNB's.The outputs from each LNB will go to a separate 4x1 switch,and from switch to receiver. (3) 22Khz switch; 2 required for this installation,as well as 2 dual LNB's.The outputs from each LNB will go to a separate 22Khz switch,and from switch to receiver. (4) 4x4 multiswitch; 1 required for this installation,as well as 2 dual LNB's.The outputs from LNB #1 will go to Sat A inputs,and the outputs from LNB #2 will got to Sat B inputs.Do not be concerned with the 18v and 13v allocation,as the switch "freezes" these voltages within the unit.Set 1 sat to 22Khz ON,and the other to OFF(in your settings). This unit can drive up to 4 receivers.
Three LNB;s to one receiver...........As much as we hate to say so,the 4x1 diseqc switch is the simplest(although not the most efficient) switch for this job.As the cost of these has dropped,so has the quality.
Four LNB's to one receiver..........Again,reluctantly,the 4x1 diseqc is the simplest choice.
Two LNB's to three receivers..........4x4 multiswitch
Two LNB's to four receivers............4x4 multiswitch
-------------------------------------------------------------------------------- 1 LNB = 1 sat bird..but for Dishnetwork TV, most people want 2 satellites,the 110 and 119 birds reception on each receiver..
-------------------------------------------------------------------------------- LNBF 1. Legacy: a. single: called single legacy, one output. b. dual: called dual legacy, 2 outputs. c. twin: big fat lnbf, 2 outputs, has 2 SW21 switch built-in. (sw21 is not for FTA) d. quad: big fat lnbf, 4 outputs, has 4 SW 21 switch built-in. (sw21 is not for FTA)
2: DishPro a. single: called single DishPro, one ouput. b. dual: called dual DishPro, 2 outputs. c. twin: big fat lnbf, 2 outputs, has 2 independent Diseqc switch built-in (FTA-yes) d. quad: big fat lnbf, 4 outputs, has 4 independent Diseqc switch built-in (FTA yes)
Dish Pro twin LNB gets both the 110 and 119 on 2 receivers..and no switches needed...
Dish pro LNB's cannot use legacy channel lists...need DP channel lists
DUAL LNB is for 1 satellite signal (example 110) and 2 receivers...TWIN LNB aka fatboy/fathead is for 2 satellites ( Example..110 and 119) AND 2 receivers .. there is much confusion about DUAL vs TWIN LNB's