|
New member Username: CrafthellPost Number: 1 Registered: Oct-07 | I'm currently Running a CRUNCH 800watt amp with 2x 12" Dual 4 ohm CVR's wired for mono 4ohm bridge (400watt x 2 subs) so far it runs good but what should i be putting the LEVEL, BASS EQ, LP FILTER, and last HP FILTER settings at for KiCKER CVR's Crunch PZi 125.4 Amplifier Specifications: * RMS @ 4-Ohms: 125W x 4-Ch * RMS @ 2-Ohms: 200W x 4-Ch * RMS @ 4-Ohms: 400W x 2-Ch * Dynamic Music Watts * SEPP A/B-Class PZi Amplifier Designs * Bridgeable Design * s Illuminated, Large New Design Crunch Logo * PZi. MOSFET Pulse Wave Modulated Power Supply For Instant Maxx Current Output * 2-Ohm Capable A/B Class * Config to 3-Ch R & L and Sub Mode * Rugged MOSFET Audio Outputs * PZi Amp Protection with System Diagnostics LED's That Protects Against: o Current / Amperage Overload o Short Circuits o Thermal Overload o DC Offset * Hi-Level Speaker Lead Inputs * Silver Preamp Level RCA Inputs * Daisy Chain Line Outputs * Versa Cross Sound Shaping Controls: o Mono/Stereo Switch o HP/LP/Full-Pass Freq. Selections o Crossover Frequency Adjustments: 60 Hz to 1.2kHz o (30 Hz to 250 Hz Low-Pass) * Separate F & R Bass EQ Controls Adjustable +12dB Bass EQ @ 45Hz * Input Level Control (0.2 to 5V) * Oversized Speaker Terminals[/code] 2x Kicker 07CVR12-4 Subwoofer Specifications: * Sensitivity: 86.7 dB * RMS Power Range : 400 Watts * Peak Power Handling: 800 Watts * Impedance: Dual 4 Ohm * Low Frequency response: 25 Hz * High Frequency Response: 500 Hz * Diameter: 12 Inch * Santoprene surround on the edges * Injection-molded polypropylene cone * Aluminized coating * Stamped-steel basket with perimeter venting * Spiralead tinsel-lead technology * Polyamide high-temp former * Dual, high-temp (428 degrees F) voice-coil wire * Polycotton spider for improved linearity at high volumes * Progressive-roll Thanks, Craft |
|
Gold Member Username: JuliobSanto DomingoDominican Re... Post Number: 4966 Registered: Dec-05 | hifonics Bxi 1206D for you |
|
Silver Member Username: Hurricanebr1anWestern Burbs of Chicago, IL Usa Post Number: 162 Registered: Sep-07 | you have an amp that pushes a *rated* 400wrms, consider upgrading the amp if you want the cvrs to reach their potential. 800 + wrms depends on amp. |
|
New member Username: CrafthellPost Number: 2 Registered: Oct-07 | k thanks for the input so theres really no way i could blow these subs with this amp? but u didn't answer my question what settings can i set the amp at? i already bought that amp for 89$ new and the 2x kickers @ 155$ total... if need be ill upgrade amp later but they are pretty damn loud even if it doesn't push a total of 800 watt.. i turn it past 4 on most songs on the head unit and my head hurts lol.. and i think it goes to 30-40 |
|
New member Username: CrafthellPost Number: 3 Registered: Oct-07 | i found the: Hifonics BXi 1206D 2400-Watt Brutus Mono Amplifier for $234 @ onlinecarstereo.com (63% off retail) if i buy this amp what settings can i put it at?} |
|
Silver Member Username: •cam•Post Number: 837 Registered: Nov-06 | http://www.subwoofertools.com/forum/setgain.asp how to set your gains. Set the cross over where you like. No bass boost. |