|
Silver Member Username: Snarl2004Earthquake Amp Post Number: 267 Registered: Dec-06 | should i get 2 12" SD2.5's or 1 12" HD3 my amp puts out 1000rms |
|
Gold Member Username: Logan__tille[:-]15 Wangers Club[:-] Premier Member Post Number: 5563 Registered: Feb-06 | SD2.5 |
|
Gold Member Username: Denali_on_22sSSX, Tenneki US of A Post Number: 1259 Registered: Feb-06 | ^^^x2 |
|
Gold Member Username: Logan__tille[:-]15 Wangers Club[:-] Premier Member Post Number: 5564 Registered: Feb-06 | what amp do you have? Does it put out 1000 at 1ohm? |
|
Silver Member Username: Snarl2004Earthquake Amp Post Number: 269 Registered: Dec-06 | puts out 1000rms at 2ohm and its 1ohm stable but i think it still only puts out 1000rms |
|
Silver Member Username: Rosrock2000Notre dame!USA Post Number: 266 Registered: Dec-06 | just tell the exact amp model number |
|
Silver Member Username: MgbcsLincoln, Nebraska Post Number: 350 Registered: Dec-06 | It should put out more at 1 ohm than 2 ohms...what's the model? |
|
Silver Member Username: Snarl2004Earthquake Amp Post Number: 271 Registered: Dec-06 | earthquake ph2000w/d1.1 the web site says 1000rms at 1 ohm but i have the 2006 model and the manual says 1000rms at 2 ohms and its 1ohm stable http://earthquakesound.com/powerhouse_amplifiers.htm |
|
Silver Member Username: Snarl2004Earthquake Amp Post Number: 272 Registered: Dec-06 | didnt bump |
|
Gold Member Username: Logan__tille[:-]15 Wangers Club[:-] Premier Member Post Number: 5566 Registered: Feb-06 | ok it will be fine...SD2.5 |
|
Silver Member Username: Snarl2004Earthquake Amp Post Number: 273 Registered: Dec-06 | i beleive the sd2.5's are svc so i parallel wire them as if it was a dual 4 ohm sub to get a 2ohm load right? and how many cubic feet should i have per sub? |
|
Silver Member Username: Snarl2004Earthquake Amp Post Number: 274 Registered: Dec-06 | s**t nvm there dual 4ohm coils sry...how much cubic feet per sub? |
|
Silver Member Username: Snarl2004Earthquake Amp Post Number: 275 Registered: Dec-06 | also i should wire them for a 2ohm load right? |
|
Silver Member Username: Rosrock2000Notre dame!USA Post Number: 267 Registered: Dec-06 | well if they are dual 4's then ud wire them in parrelell and this would give u an overall 1 ohm impedence.. |
|
Gold Member Username: Logan__tille[:-]15 Wangers Club[:-] Premier Member Post Number: 5568 Registered: Feb-06 | DJ (the owner/builder) will design you a box. |
|
Silver Member Username: Snarl2004Earthquake Amp Post Number: 277 Registered: Dec-06 | i have a chevy s10 extended cab truck...i have to make sure i have enough room to make the box the required volume behind the seats. i dont want to buy the subs then figure out i dont have enough enough room to make a box for the subs |
|
Silver Member Username: Snarl2004Earthquake Amp Post Number: 279 Registered: Dec-06 | or does anyone have a 12" SD2.5 if so what is ur cubic ft and tuning hz? |
|
Gold Member Username: AdddisorderWest palm, Florida Post Number: 3073 Registered: Jan-06 | 2-2.5 each tuned to 32 would be good for them |