Help tsw3004spl
|
New member Username: Gwidas06Post Number: 3 Registered: Nov-06 | Hi i have pioneer tsw3004spl(1000rms 2ohm) sub I am going to use an amp wich puts out 1700rms 2ohm(boss audio ripper series 3000max). Will my sub handle that power? Is it better to turn down input sensitivity of the amp? Is 4awg cables enough for the amp? I have 140amp fuse short circuit braker if its to much then what size of fuse would i need? What size of cables would i need to wire the sub to the amp? |
|
Gold Member Username: Basshead86OG eCoustics Member Post Number: 8680 Registered: Aug-05 | http://www.the12volt.com/info/recwirsz.asp input sensitivity of the amp should be matched to the HU's pre-out voltage, nothing else. that way you get the cleanest possible signal going to the subs.  |
|
New member Username: Gwidas06Post Number: 5 Registered: Nov-06 | But will i damage the sub? |
|
Gold Member Username: RovinTrinidad & T... Post Number: 9783 Registered: Jul-05 | by chance r u from T&T ? since that sub/amp combo is very popular here & i also notice ur car in ur profile ........ |
|
New member Username: Gwidas06Post Number: 6 Registered: Nov-06 | no im from lithuania but living in irelan these last 3 years |
|
Gold Member Username: RovinTrinidad & T... Post Number: 9786 Registered: Jul-05 | oh ok cool i have same sub as u but mine is the dual 2ohms model 3002 i hope u know these subs only seem 2 perform in large ported boxes i had mine in 3cuft box but sub like it wanted more so yesterday i put mine in a 4cuft box - sounds better but i need 2 tune it a bit higher 4 some more output is that a boss D3 ripper u have ? - those only put out 1000wrms RIPD3 Class D Monoblock Digital Power Amplifier With Remote Subwoofer Level Control SPECIFICATIONS RIPPER Monoblock Amplifier Max power, 2 ohm 2200w x 1 RMS power, 4 ohm 1200w x 1 Bridged power N/A Max Power 3000w x 1 Signal-noise-ratio >100dB THD .05 % Dimensions, 11 1/2" W x 2 1/2"H x... 12 7/8" ......... |
|
New member Username: Gwidas06Post Number: 7 Registered: Nov-06 | Ripper Chrome / Gold RIP-D3 Class D Digital Monoblock Amp. 1200 Watts RMS into 4 Ohms, 1700 Watts RMS into 2 Ohms, 3000 Watts max output and 2400 Watts RMS Bridged into 4 Ohms!!!! (Requires 2 of these for bridging! Signal-noise-ratio >105dB. http://cgi.ebay.ie/Boss-Audio-3000-Watt-Chrome-Gold-Car-Amp-Amplifier_W0QQitemZ2 50050093055QQihZ015QQcategoryZ18797QQtcZphotoQQcmdZViewItem |
|
New member Username: Gwidas06Post Number: 8 Registered: Nov-06 | What way you wire your sub 1ohm or 4ohm? |
|
Gold Member Username: JuliobSanto DomingoDominican Re... Post Number: 3380 Registered: Dec-05 | don't worry too much about overpowering with that amp, just match your gain with you HU preout voltage. What's HU do you have?? Rovin i didn't know you're using pioneer subs right now, i thought you were using FI |
|
New member Username: Gwidas06Post Number: 9 Registered: Nov-06 | pioneer deh-p7800mp |
Main Forums
Today's Posts- Home Audio Forum
- Home Video Forum
- Home Theater Forum
- Car Audio Forum
- Accessories Forum
- All Forum Topics