Flat Wind Coil on SSD???
|
Silver Member Username: Freezeman_7Lindsay, Oklahoma Post Number: 287 Registered: May-06 | hey guys. muddy finally talked me into the fi ssd's i think i will be really happy.. now i plan on ordering them by the end of the week. so do i want Flat Wind Coil? or no. and Dual 1 or Dual 2. i cant find any wiring diagrams that show me how to wire dual 1 ohm subs. but ive found dual 2 and it can be wired to 2ohms or .5 ohms. so does anyone no of a 2000wrms sub @2ohms... thanks |
|
Gold Member Username: DrsmithMontana USA Post Number: 1032 Registered: Nov-04 | how about 2 1000 watt amps? |
|
Gold Member Username: FrkkevinLake Worth, Texas US Post Number: 1018 Registered: Nov-05 | DVC 1 ohm can be wired to 0.5 ohm or 2 ohm DVC 2 ohm can be wired to 1.0 ohn or 4 ohm So as far as which coild type depends on what type of amp you have or are going to run. I'm not expert and don't know much about the difference between the coils but subs with the flat wind coil tend to be the better buy. I've been told the differene but can't remember it... ugh. Something about allowing the coil to flow more current.. more surface area.. |
|
Gold Member Username: FrkkevinLake Worth, Texas US Post Number: 1019 Registered: Nov-05 | oh whoops.. sorry. did not see you were getting two.. completely changes the wiring.. what i posted was for single sub |
|
Silver Member Username: Freezeman_7Lindsay, Oklahoma Post Number: 289 Registered: May-06 | nope dvc 2 ohm cant be wired to one. according to crutchfield and the 12volt. here ill show you 2-ohm DVC .5-ohm load, 2-ohm load, or 8-ohm load http://www.crutchfieldadvisor.com/learningcenter/car/subwoofers_wiring.html?subs =2&impedance=DVC2x2 i just cant find a diagram dvc 1ohm |
|
Silver Member Username: Freezeman_7Lindsay, Oklahoma Post Number: 290 Registered: May-06 | oh my bad then... haha its cool yep 2 twelves. jus cant decide on dual 1 or 2 and flatwind or not? |
|
Gold Member Username: Basshead86Try Google Post Number: 6549 Registered: Aug-05 | The flatwind allows for a little more coil(increasing overall strength and lowering the qts)in the gap as well as a little better power handling.  |
|
Silver Member Username: Freezeman_7Lindsay, Oklahoma Post Number: 292 Registered: May-06 | sweet. so go for the flat wind? ok. now dual 1 or dual 2 ohm. think you know if im gonna buy the sub why not get it done right. so ill def do the flat wind |
|
Gold Member Username: Basshead86Try Google Post Number: 6552 Registered: Aug-05 | the ohm config will depend on what amp you get...more than likely though you will want the Dual 2 ohms to get a final impedance of 1ohm for the amp. |
|
Gold Member Username: RovinTrinidad & T... Post Number: 9245 Registered: Jul-05 | u only live once so u might as well stop pinching pennies get it fully modded .... ...  |
|
Gold Member Username: Basshead86Try Google Post Number: 6555 Registered: Aug-05 | LOL^^^ he has a point ladies and gentleman..  <---and aren't these sweet???? lmf*ckingao |
|
Gold Member Username: RovinTrinidad & T... Post Number: 9247 Registered: Jul-05 | eeeeeew no ! ^ that looks like a guy wit T/I/T/S ..... |
|
Silver Member Username: Kaos15thPost Number: 218 Registered: Mar-05 | these are better lol  |
|
Gold Member Username: RovinTrinidad & T... Post Number: 9248 Registered: Jul-05 | well since the forum is quiet now & u all r bringing out pix ......>>>>>>>>>     |
|
Gold Member Username: DrsmithMontana USA Post Number: 1039 Registered: Nov-04 | ^^^^^ nice |
|
Silver Member Username: Kaos15thPost Number: 220 Registered: Mar-05 |     |
|
Silver Member Username: Freezeman_7Lindsay, Oklahoma Post Number: 296 Registered: May-06 | you cant wire a dual voice coil 2ohm sub to 1ohm. its impossible. or tahts what crutchfield and the12volt says... |
|
Silver Member Username: Freezeman_7Lindsay, Oklahoma Post Number: 297 Registered: May-06 | ordering 2NITE. FI SSD 12' (2) Flatwind coil Dual Voice Coil 2OHM |
|
Gold Member Username: Cenus4, 2 0 Post Number: 2340 Registered: Jan-05 | whats the rms on those subs, i think there 1000wrms, if so i'd look for a kx2500.1, it does 2500wrms@2ohm, wire 2 dvc2ohm series/parrellel for a 2ohm load. |
|
Gold Member Username: Cenus4, 2 0 Post Number: 2341 Registered: Jan-05 | whats the rms on those subs, i think there 1000wrms, if so i'd look for a kx2500.1, it does 2500wrms@2ohm, wire 2 dvc2ohm series/parrellel for a 2ohm load. |
|
Silver Member Username: Freezeman_7Lindsay, Oklahoma Post Number: 304 Registered: May-06 | exactly someone who understands me. it has to be at 2 ohms. thank you dustin. |
|
Silver Member Username: Freezeman_7Lindsay, Oklahoma Post Number: 305 Registered: May-06 | exactly someone who understands me. it has to be at 2 ohms. thank you dustin. |
|
Gold Member Username: Cenus4, 2 0 Post Number: 2342 Registered: Jan-05 | NP man, just remember to upgrade the alt, with that much power. |
|
Silver Member Username: Freezeman_7Lindsay, Oklahoma Post Number: 308 Registered: May-06 | oh yeah i know it. ive been lookin for about a 180-200amp alt. havent had any luck yet tho |
|
Silver Member Username: Freezeman_7Lindsay, Oklahoma Post Number: 309 Registered: May-06 | https://www.ecoustics.com/electronics/forum/car-audio/275082.html |
|
Gold Member Username: Basshead86Try Google Post Number: 6608 Registered: Aug-05 | post pics when you get them |
Main Forums
Today's Posts- Home Audio Forum
- Home Video Forum
- Home Theater Forum
- Car Audio Forum
- Accessories Forum
- All Forum Topics