New member Username: MaekonePost Number: 2 Registered: May-06 | Hey I just bought 2 12" Gt4-12 JBL subs, I was just wondering if any one knew of a good 2 channel, 1000w amp to power them and if that would be my best option. heres the specifications for one of the subs. RMS - 250w Peak - 1000w Frequency Response - 28Hz-450Hz Sensitivity - 93dB Impedance - 4 Ohms Cheers Maek |
Silver Member Username: CtmikeCt. Post Number: 976 Registered: Feb-06 | a 1000w amp would probably blow those subs. look at the rms, not the peak. try and find a good mono amp that puts out 500-600w. what's your budget for an amp? |
Gold Member Username: JuliobSanto DomingoDominican Re... Post Number: 1214 Registered: Dec-05 | JL 500/1 PG 600.1 or alpine mrd 605 |
Gold Member Username: Dustin3Tigard, Or U.S. Post Number: 2215 Registered: Oct-05 | juliob, what about the HIFONICS BXi606? ha kicker kx600.1 |
Gold Member Username: JuliobSanto DomingoDominican Re... Post Number: 1225 Registered: Dec-05 | not that hifo jeje, cuz it should be putting like 400w jeje. |
Gold Member Username: Dustin3Tigard, Or U.S. Post Number: 2227 Registered: Oct-05 | haha. i was thinkin around 500. haha |
New member Username: MaekonePost Number: 3 Registered: May-06 | 200-300 dollers. Would a mono amp run both subs? |
Gold Member Username: Dustin3Tigard, Or U.S. Post Number: 2251 Registered: Oct-05 | of course they will. you need an amp that does 500-600 @ 1 or 4 ohms. it doesnt matter if mono block or 2-channel. kicker kx600.1 is a great amp ---- as so the pheonix gold xenon 600.1 |
Silver Member Username: JohnfiacIl USA Post Number: 263 Registered: Mar-06 | i would look for a mono amp that does about 800rms or so at 2 ohms and wire the subs like that and connect the subs for the 2ohm load instead of 4... |
Gold Member Username: JuliobSanto DomingoDominican Re... Post Number: 1259 Registered: Dec-05 | first thing, those JBL are 4 SVC, if they are try getting a 2 ohm stable amp such as alpine mrd605, PG xenon 600.1, JL 500/1. If they're dual 4 ohm, try getting an amp 1 or 4 ohm stable, Directed d1200, check orion 600d, PG xenon 600.1 (again jeje with jl 500/1.) |
New member Username: MaekonePost Number: 4 Registered: May-06 | What about this, would it get the job done well? Specifications: Power / channel @ 4ohm 14.4V: 400WRMS x 1 Power / channel @ 2ohm 14.4V: 700WRMS x 1 Power / channel @ 1ohm 14.4V: 820WRMS x 1 Signal/Noise ratio: >90dB Input sensitivity: 200mV - 6V Low pass filter: 35 - 300Hz @ 12dB/octave Bass boost: 0 - 18dB @ 30 - 120Hz Subsonic filter: 10 - 60Hz Remote level controller: Yes Dimensions: 324(L) x 258(W) x 50mm(D) https://secure4.vivid-design.com.au/jaycar2005/productView.asp?ID=AA0428&CATID=& keywords=car+amp&SPECIAL=&form=KEYWORD&ProdCodeOnly=&Keyword1=&Keyword2=&pageNum ber=&priceMin=&priceMax=&SUBCATID= Cheers Guys. |
Gold Member Username: Dustin3Tigard, Or U.S. Post Number: 2332 Registered: Oct-05 | yes. that would work. wut amp it that? |
New member Username: MaekonePost Number: 5 Registered: May-06 | AA-0428 from jaycar. this is the link https://secure4.vivid-design.com.au/jaycar2005/productView.asp?ID=AA0428&CATID=& keywords=car+amp&SPECIAL=&form=KEYWORD&ProdCodeOnly=&Keyword1=&Keyword2=&pageNum ber=&priceMin=&priceMax=&SUBCATID= |