New member Username: Sean_dubPost Number: 1 Registered: Feb-06 | I am most likely going to purchase 2 Pioneer Premier TS-W5000SPL subwoofers, and I need to know what kind of amp I should use to power them with. They handle 2000 rms, 5000 peak, and are Dual 4 ohm subs. What I want to know is should I get an amp (or multiple amps) that run 4000 rms x 1 channel @ 1 ohm, 2000 rms x 2 channels @ 2 ohm, or 2000 rms x 2 channels @ 4 ohm? My past systems only had one sub and one amp, like the Audiobahn Immortal (decent sound, poor durability) and a MA Audio HK401SX. I have a pretty good budget, and am looking at Memphis and Rockford Fosgate mainly to get the amps neccessary. Thanks |
Gold Member Username: Chaunb3400Huntsville, Alabama U.S. Post Number: 5289 Registered: Jul-05 | any reason why u are getting the pioneer's?? |
New member Username: Sean_dubPost Number: 5 Registered: Feb-06 | my friend has a lower series, maybe the ts-w3004spl, and they hit pretty hard. If you wanna suggest something else go ahead, I just need to know how the amps and subs are set up as far as channels and outputs go, so I can figure out what all to buy. It's just that the 2 ts-w5000spl subs are decently cheap, handle a lot of power, and don't take up a lot of space. |
Gold Member Username: TjmutlowPost Number: 1428 Registered: Sep-05 | maybe a orion 2500d |
New member Username: Sean_dubPost Number: 7 Registered: Feb-06 | I'm not looking for advice on what amp to buy, I just wanna know how the hookup between amp and subs works. Each sub will have a 2 ohm impedance, for a 1 ohm total load. Can I run both off a single channel running at 1 ohm? Or do I need to find something running at 2 channels, with each channel being 2 ohms? Thanks |
Gold Member Username: TjmutlowPost Number: 1438 Registered: Sep-05 | what amp do you think your going to run, run it at 1ohm, and it needs to be the 4001bd for fosgate and for memphis the 4000w amp with the bridge module @a 1ohm load. it will be the most efficient way to run them. hard to find a 2 channel that will support that much power needed. |
New member Username: Sean_dubPost Number: 8 Registered: Feb-06 | So I can run two subs off one channel? I was looking at the Memphis amps and the Hifonics XX series, and I just wanted to be sure I can run a pair of subs with only one output channel before I make any decisions. |
Gold Member Username: TjmutlowPost Number: 1443 Registered: Sep-05 | yes as long as it is 1ohm stable and can support the wattage you need, youll need HO alt and xtra battery at least |
New member Username: Sean_dubPost Number: 9 Registered: Feb-06 | Yeah, I looked into the HO alternators, I'm gonna get one of them. Tell me anything you know about this amp and brand, if you dont mind: MA Audio HK802SX. It puts out 4400 RMS @ 1 ohm bridged. It says high current, I dont know what that refers to, does it just mean it will draw more from the alternator? Anyway, check it out at http://www.sonicelectronix.com/item_2682.html |
Gold Member Username: TjmutlowPost Number: 1445 Registered: Sep-05 | if you really want to use MA, use 2 hk4000d amps, 1 per sub, they are rated at 3600w@14.4volts @2ohms. and 4000 @17volts@2ohms. If you really want to push some power to those subs. |
Gold Member Username: RovinTrinidad & T... Post Number: 5495 Registered: Jul-05 | if were me i'd get 2 separate amps like kicker 2500.1 which does over 2500wrms @ 2ohms ...... |