|
New member Username: Billytheclub2Brentwood, Ca Usa Post Number: 1 Registered: Oct-05 | I just bought an MA Audio AMP HK897 and two S12L5 kicker solorberic subs what would be the best way to wire them up? And the subs are dvc 2ohm and the amp is 300W x 2 RMS @ 4 Ohm Stereo 500W x 2 RMS @ 2 Ohm Stereo please help lol. |
|
Silver Member Username: Chaunb3400Huntsville, Alabama U.S. Post Number: 580 Registered: Jul-05 | http://www.the12volt.com/caraudio/woofer_configurations.asp http://www.bcae1.com/ Check these out |
|
New member Username: Billytheclub2Brentwood, Ca Usa Post Number: 2 Registered: Oct-05 | that did not help me but thanks.. |
|
Silver Member Username: Chaunb3400Huntsville, Alabama U.S. Post Number: 595 Registered: Jul-05 | parallel |
|
Silver Member Username: SolacedagonyNew Jersey US Post Number: 543 Registered: Oct-04 | If that didn't help you then you didn't read them. You need to learn Ohm's law to learn how to wire your amps to your subs. |
|
New member Username: Billytheclub2Brentwood, Ca Usa Post Number: 3 Registered: Oct-05 | can anyone elae one help me???? |
|
Gold Member Username: CarguyPost Number: 4861 Registered: Nov-04 | Billy, you have a bad combo. For your subs to maximize the amp, they needed to be 4ohms DVCs. With 2ohms DVCs, your only option is to use them in the 4ohm mode by connecting each VCs in series. Then you will get 300w x 2 @ 4ohms. Don't try and bridge the amp. It will only handle 4ohms load. Your subs will only configure to 2ohms,.5ohms or 8ohms. If you had an amp that was 2ohms stable in bridged mode, then it would've worked out great. |
|
Silver Member Username: FandimReno, Nevada United State... Post Number: 362 Registered: Jun-05 | You should avoid wiring seperate subwoofers in series connection, btw... (if wiring voicecoils, series is ok, but with two seperate subs, avoid series if at all possible). Seth |
|
New member Username: Billytheclub2Brentwood, Ca Usa Post Number: 4 Registered: Oct-05 | 1200 watt high power 2 channel bridgeable hard kore series car amplifier 1200 x 1 RMS bridged 500 x 2 RMS @ 2 ohms this is the amp Isaac is it bridgeable???? |
|
New member Username: Billytheclub2Brentwood, Ca Usa Post Number: 5 Registered: Oct-05 | and 300W x 2 RMS @ 4 Ohm Stereo |
|
New member Username: Billytheclub2Brentwood, Ca Usa Post Number: 6 Registered: Oct-05 | thanks you all but i do not get the ohm law??? but can sum one look at the amp 1200 watt high power 2 channel bridgeable hard kore series car amplifier 1200 x 1 RMS bridged 500 x 2 RMS @ 2 ohms 300 x 2 RMS @ 2 ohms Overload, Short and Thermal Protection Circuit Platinum plated RCA terminals Frequency Response: 20 Hz - 20 kHz Full Mosfet Circuitry Selectable Bass Boost @ 50Hz 2 ohm stable 50dB Channel Separation RCA Line in and out Built in advanced high pass and low pass and flat selectable crossovers 90dB Signal Noise Ratio 22K Ohm Input Impedance Stainless Steel Heatsink Pre-Amp Outputs Built in high powered fan 200mV-2V Input Sensitivity THD <0.05% Selectable Bass Boost (0db - 18dB) 50Hz - 250Hz Low Pass Filter Fuse Rating: 40A x 2 Dimensions: 2.7"H x 12.4"W x 13"L |