Conversion BIN PUFF_297

 

Platinum Member
Username: Nydas

Post Number: 13037
Registered: Jun-06
PUFF_297 for FLU/2500 Conversion to 2700
Full kits for Latest conversion BINs and other files - also for Revert to 2500

Alternative PUFF link
Alternative PUFF link

Download and unzip into separate directory.
PLEASE DO NOT ATTEMPT WITHOUT READING INSTRUCTIONS.
 

Silver Member
Username: Fahadriz8

Post Number: 147
Registered: Aug-06
is there any freezing with this bin?
 

Silver Member
Username: Kingofdakingz

Post Number: 372
Registered: Jun-06
no its working good for me since 3 hours now so i think its good
 

Bronze Member
Username: Mrgreg

Ont. Canada

Post Number: 80
Registered: Dec-07
Works good.
 

Silver Member
Username: Snw7619

Bahamas

Post Number: 233
Registered: Oct-06
nalin is this for B-75 pansat2700 converted. for freezing?
 

Platinum Member
Username: Nydas

Post Number: 13041
Registered: Jun-06
There is no b75 version of conversion 297. I think, though b75 conversion BINs work well, there is not enough support, so I suggest everybody should go the PUFF route.
 

Bronze Member
Username: Mrgreg

Ont. Canada

Post Number: 86
Registered: Dec-07
b-75 297 bin is out at Crazyfta
 

New member
Username: Mainsource

Post Number: 1
Registered: Nov-08
I just converted to PUFF and loaded the PUFF_297 bin but it's not working. Is this bin still working or is it down? Thanks.
 

Platinum Member
Username: Nydas

Post Number: 13058
Registered: Jun-06
PUFF_297 is working fine.
Try loading it again.
did you rescan??
 

New member
Username: Mainsource

Post Number: 2
Registered: Nov-08
Thanks for the response Nalin. I've tried reloading the bin. Tried rescanning. Tried setting the default key. Still getting the scrambled or bad channel message.
Since it's my first time converting to PUFF and using a PUFF bin, I thought I might of done something wrong but I don't think I have.
 

Platinum Member
Username: Nydas

Post Number: 13068
Registered: Jun-06
Converting PUFF requires that you install the 253 PUFF Boot/BIN 640K
Then you install the PUFF BIN.
Full instructions are there in the PUFF kit.
If there is a problem start with installing b60 BOOT followed by the old 294T and then do the full conversion.
Going the full root you MUST do use setup and rescan the sats.
 

New member
Username: Mainsource

Post Number: 3
Registered: Nov-08
I installed everything as instructed. Still nothing. Is Bev working for this bin?
 

Platinum Member
Username: Nydas

Post Number: 13088
Registered: Jun-06
BEV is NOT working for ANY FTA receiver except partly on Nfusion.
 

New member
Username: Mainsource

Post Number: 4
Registered: Nov-08
Ah no wonder it's not working for me. Dishnet is working but I've never used it before. What satellite is for Dishnet and which way do I point the dish?
 

Platinum Member
Username: Nydas

Post Number: 13093
Registered: Jun-06
BEV is 82/91 degrees.
DN is 110/119 degrees
Note the 9 degrees difference.
Swing the dish 28 degrees and you should get it. You will need to adjust elevation direction as well
 

New member
Username: Mainsource

Post Number: 5
Registered: Nov-08
Thanks Nalin. I'll give it a try on a nicer evening. It's raining out there.
 

Bronze Member
Username: Vinnyc

Mb Canada

Post Number: 21
Registered: Dec-07
my viewsat when down tonight, so I am usinf my old receiver pansat 2700 clone and is working just fine try using bin 297. it works with out frezing.
« Previous Thread Next Thread »



Main Forums

Today's Posts

Forum Help

Follow Us