Panstat 3500SD and Dishpro plus LNB

 

Bronze Member
Username: Paulb

Post Number: 20
Registered: May-06
Panstat 3500SD and Dishpro plus LNB, are the two compatible?? I seem to have issues changing LNB Type on Antenna, Satelite setup. Some Transponders I receive well with Dishpro, and others I use single stack. Is there a good rule for this... or is it a physical LNB issue?
 

Platinum Member
Username: Lklives

Post Number: 12485
Registered: Jan-06
DPP LNB's work well with ALL receivers...U have a newbie problem..
 

Bronze Member
Username: Paulb

Post Number: 21
Registered: May-06
You are right.. can you give me any direction??

You seem to be very active here, giving alot of people advise... That is good of you
 

Platinum Member
Username: Lklives

Post Number: 12489
Registered: Jan-06
Use the same exact antenna settings as DP..dish pro...and provide much more info..

which sats...how many LNB's...switches...LNB type (single, dual, twin, quad)

usually its a DPP TWIN LNB (2 sats)...

1 cable directly to 1 FTA receiver...if U have a 3rd satellite then u will need to power the LNB's with a DN receiver or a power inverter...

Twin settings

119-port #1....110- port #2
type-OSD-DP
freq 11250
scan all
22- off



if U have a 3rd sat and LNB then , do this...(legacy is a DN receiver for extra power)...and always leave the DN receiver on..if ONLY the DPP twin, then no need for the DN receiver..


Upload
 

Bronze Member
Username: Paulb

Post Number: 22
Registered: May-06
I have a Dishpro Plus Digital LNBF

I am pointing to 110 and 119, Echo 8.6/Ku and Echo 1.2/Ku, trying to get Orlando FL local channels

I am getting some channels but not many. I have been connected as diagram above
 

Platinum Member
Username: Lklives

Post Number: 12497
Registered: Jan-06
U need the DN receiver powered ON always to power the LNB's...and U need your dish aligned and the settings as posted above, but add the echo 1.2 settings also..to port #4

U will ONLY get Orlando locals, if U live near Orlando...
 

Bronze Member
Username: Paulb

Post Number: 23
Registered: May-06
I don't understand your ports?? Do you mean DisEqc?
 

Platinum Member
Username: Lklives

Post Number: 12501
Registered: Jan-06
yes....each input on the disque switch is numbered..and must be the same # as U input into the receiver antenna settings...how else would your receiver know what U have done?
 

Bronze Member
Username: Espn3

Post Number: 86
Registered: Aug-06
LK, I need your help.
I have DN ( E7, E8 ) for 2 receivers comming out of 2 LNBs, each with 2 outputs similar to the picture DPPLUS of your post on 9/30, 5:17pm.
The problem I have is that I don't get anything above 12,200MHz ( on TP Scan quality goes to 0 above 12,200MHz on both E7, E8 ). Under antenna setup, satellite, I have LNB Local-Freq. = 10750.
Is there a setting problem or a LNB problem ?
If it's a LNB problem can you recommend a reputable site to buy a similar device ( twin LNB ) with the DPPLUS ( 2 LNBs, each with 2 outputs ) and be able to see above 12,200Mhz ? Are there such devices with 3 or 4 outputs from each LNB ? Or 3 or 4 LNBs in the same device, each with multiple outputs ? Thanks.
 

Platinum Member
Username: Lklives

Post Number: 12552
Registered: Jan-06
setting should be 11250...not 10750, thats for linear LNB's and freqs..
 

Bronze Member
Username: Espn3

Post Number: 88
Registered: Aug-06
LK, after I changed to 11250 I get quality ONLY above 12200 ( TP scan ). Do I need to adjust the antenna ? thanks.
 

Platinum Member
Username: Lklives

Post Number: 12584
Registered: Jan-06
U need to do a scan and tell us what happens EXACTLY, along with ALL your antenna settings...after U do a reboot,set the date and time, and wait while keys update with bin 330 ...

U must provide the complete scenario..this bits and pieces, don't hack it!
 

Bronze Member
Username: Espn3

Post Number: 89
Registered: Aug-06
LK, I have 2 FLUs converted to Pansat 2700 and use the jvvh_213_Td.bin which works great.
I'll do a new scan and let you know. Thanks.
 

Bronze Member
Username: Kardary7

Nashville, T.N

Post Number: 12
Registered: Apr-07
hi
i want help
i don't know what happen with my ppvu channal or BVE channal ,so any bady know what is wrong or where i can found the new file for pansat 3500sd pleas pleas help thank}}}}
 

Silver Member
Username: Rtap

FL

Post Number: 521
Registered: Jan-07
you can find these files or info at these websites.

future-fta*info
ftabins*net
replace the * for . and register.
all you may need is the current bin file with autoroll fix.
the latest file for 3500 is x-05bl 070929 330api.zip
 

Platinum Member
Username: Lklives

Post Number: 12628
Registered: Jan-06
Bec has minor ECM going on...READ this site about it!
 

Gold Member
Username: Jmill1948

Chester, Va Usa

Post Number: 1072
Registered: Apr-04
Thats a fine setup.....after you get a list in chage it to echostar package.works much better
« Previous Thread Next Thread »



Main Forums

Today's Posts

Forum Help

Follow Us