Help - Setting up of Second Dish

 

Silver Member
Username: Yashmatharu

Brampton, Ont Canada

Post Number: 136
Registered: Feb-06
Hi Friends,

I have two receivers (Pansat 2700 FLU & CS7000 PVR) and one dish (round and may be 18") pointing at 61.5W with dual lnb. Yesterday I bought another dish to position 91W (it is not round).
Can you please confirm that the 2nd dish is right to position 91W?
 

Silver Member
Username: Banti

Post Number: 219
Registered: Jul-06
never heard of a dish that is not round. maybe u can mainly all dish can catch satellites try it.
 

Silver Member
Username: Rtap

FL

Post Number: 437
Registered: Jan-07
go to the recommended site thread by lk there you will find the list that will answer your question on dish pointing
 

Platinum Member
Username: Lklives

Post Number: 12091
Registered: Jan-06
Banti...there are many common elliptical dishes 20 x 24, which are NOT round

Yash...the 2nd dish should be fine as long as it has circular , not linear LNB, for the 91W Bev..I myself would align it towards either the 110 or 119...Bev sucks, IMO...

yes fo the the "List of recommended sites" thread here, and use ANY one of them...they all have dish pointing tips...and sat finder calculators too...

U may want to invest in a cheap $15 sat finder meter, or use an old DN unsubscribed receiver to help U align the 2nd dish...
 

Silver Member
Username: Yashmatharu

Brampton, Ont Canada

Post Number: 137
Registered: Feb-06
LK,

Thanks for your feedback. I am planning to potion to 91W only till T20 cricket world cup is over then I would put on PPV movie channels. Which one (110 or 119)has more movie channel with less adult one?
 

Platinum Member
Username: Lklives

Post Number: 12093
Registered: Jan-06
U go here and check out the various dishnet (DN) channel lists...U pick what U want...

http://ekb.dbstalk.com/dishlist.htm
 

Silver Member
Username: Yashmatharu

Brampton, Ont Canada

Post Number: 139
Registered: Feb-06
Thanks LK.
I install one more dish. Now I have two dish and two receiver therefore, have two switch. Do I need to make any changes in the settings of my receivers. I am not getting my channls after putting my cable thru switches.
 

Silver Member
Username: Yashmatharu

Brampton, Ont Canada

Post Number: 142
Registered: Feb-06
Now I am getting my channels.

I have been trying to position my dish to 91W since last couple of days but no success. Infact I don't see any other satelite other than 61.5W.
What am I doing wrong. Is 91W is in different elevation?
 

Platinum Member
Username: Lklives

Post Number: 12121
Registered: Jan-06
does it look like this?

Upload


it should...now just change the settings to correspond....

BTW...notice left side of LNB's goes to same port on each disque...same with the right side..

freq 11250
 

Platinum Member
Username: Lklives

Post Number: 12122
Registered: Jan-06
BTW...notice left side of LNB's goes to same port on each disque...same with the right side..

sorry my mistake...notice how 1 sat (LNB) goes to same port # on each switch..same with the other sat (LNB)...
 

Gold Member
Username: Tapeman

New York City in-HD, NY

Post Number: 1441
Registered: Oct-06
Yo got it right boss
It should work
They are 2 inpendent ports of the LNBs

It will be a problem if yo mismatch the DISEqC input ports.
That can affect setup during polarity switching.

But yo got it right
 

New member
Username: Rolando

Post Number: 5
Registered: Sep-07
Sorry, what I need is the master pin code for Pansat 2500a
 

Silver Member
Username: Yashmatharu

Brampton, Ont Canada

Post Number: 143
Registered: Feb-06
still finding problem in installing both satellite in my CS7000 PVR. I can only load one of them.


Do i need to make any changes in my settings? in disec, etc
 

Gold Member
Username: Crazy_greek

Post Number: 1147
Registered: Jul-06

Hey, Billy
Try 1668 and 1010
« Previous Thread Next Thread »



Main Forums

Today's Posts

Forum Help

Follow Us