BEV down today Aug 12 9:00pm
|
gigi Unregistered guest | -------------------------------------------------------------------------------- Is anyone else having problems with there BEV using atmega with nnw21d and jeepers 212010. I get a blank screen but the menus and program guide still work. |
||
|
Silver Member Username: Jmill1948Chester, Va Usa Post Number: 152 Registered: Apr-04 | changing keys | ||
|
gigi Unregistered guest | Do you have the new keys?????  |
||
|
gigi Unregistered guest | maestra.tv is down  |
||
|
Unregistered guest | Maestra.tv is now up but no new keys!!? Dsshelper says Bev is switching to Nagra2 and a card swap. Maybe, but there will still be a Nagra1. We're probably looking at a key switch-fest like the one back in the fall. Oy! | ||
|
tonymontana Unregistered guest | Damn,i read the story..these damn guys..Me also ,having the same problem.Everyone has been hit with that! | ||
|
HitmanRic Unregistered guest | BEV still down as of 1:10 central time. Some avr 6 users are having troubles too, but not all. Don't know if plastic is still up. Lost all channels around 3:00 pm local time. | ||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 36 Registered: Jun-04 | Been trying all night so far. I cant get to any of the majour hack sites to see whats up. | ||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 37 Registered: Jun-04 | most plastic seem to be up for now. | ||
|
Brandonium Unregistered guest | ROM10 card down thursday 6pm PST | ||
|
tonymontana Unregistered guest | Hey guys,IT 's working with me will all channels..What about you? | ||
|
dvldawg61 Unregistered guest | tonymontana are u using an atmega128 or MC? or if you know a site for me to try to get a good fix? thanx. |
||
|
Unregistered guest | I had the same problem. Recoded my CAM and now have all channels except PPV. Apparently there is another ECM in the stream due to Olympics. Still awaiting new updates/patches but will keep you posted as I know. | ||
|
tonymontana Unregistered guest | Im using Atmega 128 ..I am using a pfg file that a buddy made for me | ||
|
Anonymous | whats the difference between nimiq 1 and nimiq 2, they both point at the same direction and give you the same channels on BEV. I got the pansat by the way. | ||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 38 Registered: Jun-04 | nimiq 1 and nimiq 2 do not have the same channels. nimiq 2 is mostly for their internet service with a few additional channels. You have a twin LNB dish with a SW21 awitch so the channels will combine toghther from both satellites. (Anonymous please post new questions to a new thread next time) |
||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 39 Registered: Jun-04 | tonymontana if yours is working why not share your pfg file and configuration with us. I got the old nnw21-d to work but its not with all the channels. and if your running a AVR married-sub, they are not having any problems right now. | ||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 41 Registered: Jun-04 | The best pfg i have found so far is bevis v0.8. I'm running a 3100 with Atmega128 18mhz. AUX0 82 D7 51 E4 5B 97 9D 81 AUX1 65 57 46 14 36 02 D8 DA With a modified ROM3 CAM ID of S 04 51XX XXXX-XX Tiers: MIN MAX 0000 7FFF 0000 7FFF 0000 8000 8000 017F 10D0 A812 BLACKOUT STRING: D4 0F 0F D4 D4 D4 D4 D4 D4 D4 D4 D4 D4 D4 D4 This works with no freezing on most channels. PPV dont seem to work except for pron channels ? whats up with pron working and not other ppv ? Post what you got working for others to try out, thanks. |
||
|
Wanting TV Unregistered guest | I have a ? for anyone Is a Smart Card the same as a Magic Card? |
||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 42 Registered: Jun-04 | no | ||
|
Want Tv Unregistered guest | Thank's | ||
|
Sundancer75 Unregistered guest | So any solution for getting PPV channels on Bev 3100 with Atmega 128? | ||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 67 Registered: Jun-04 | ftp://fryguy.ca/Public_Files/Guides-Information/Mini_Dish_Hacking/BEV/ i have posted the new fix thats working for most channels and PPV some have freezing problems though. A better fix will be coming soon. | ||
|
Bronze Member Username: DtvPost Number: 53 Registered: Jul-04 | Jonathan fry do you know what i can get or how i can get wwe payperview events for free | ||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 73 Registered: Jun-04 | I have a new fix that seems to fix the freezing of channels that happened with the other fix. And all PPV now work! Here it is: ftp://fryguy.ca/Public_Files/Guides-Information/Mini_Dish_Hacking/BEV/ The file is ziped up and called "Latest_Atmega-128_FIX_Juggalo_X's_Mod.pfg.zip" | ||
|
Hapymen Unregistered guest | Thanks Jonathan all channels work good!! | ||
|
New member Username: MiladyIle-perrot, Quebec Canada Post Number: 1 Registered: Aug-04 | hi guys I am a newbie and i just got cut in the black out and i'm trying to find jeepers but no sites seems to works ....So how do you get jeepers without paying....Can somebody help me! | ||
|
Bronze Member Username: DtvPost Number: 56 Registered: Jul-04 | Jonathan fry do you know what i can get or how i can get wwe payperview events for free | ||
|
New member Username: MiladyIle-perrot, Quebec Canada Post Number: 2 Registered: Aug-04 | thanks jonathan fry you solved my problems !!!!! thanks kiss you men!!! |
||
|
Ty Cobb Unregistered guest | Jonathan Fry, Thanks for the awesome fix - it worked great! |
||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 76 Registered: Jun-04 | Suzanne, there is a alot of sites that have jeepers. |
||
|
Bronze Member Username: DtvPost Number: 58 Registered: Jul-04 | Jonathan fry do you know what i can get or how i can get wwe payperview events for free and jonathan what is your email address | ||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 77 Registered: Jun-04 | contact info is on my site but its fry_jonathan@hotmail.com for e-mail and instant Mesenger chat by MSN messenger. | ||
|
Anonymous | does anyone know how to get the autoroll keys for bev ? Thanks. |
||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 81 Registered: Jun-04 | anonymous, you need to be more specific then that! What are you running ? atmega, avr, etc ? Most cases just hit "get" on jeeepers to grab the latest keys on the net. |
||
|
Atmega User Unregistered guest | Thanks very much Fryguy. The "Juggalo_X's mod.pfg" file worked great on my Atmega 128. All channels work. | ||
|
Snake Unregistered guest | Is it working for AVR6 too ??? Thanks ! |
||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 85 Registered: Jun-04 | Snake, this is not a fix for the AVR's its for the atmega128's. The avr's should still be working with the same pfg just change the active public key in jeepers and do a full monty. |
||
|
sprtxtrm Unregistered guest | I can't access your fix for atmega 128, the page doesn't load. can u help??? Thanks |
||
|
New member Username: StigmataPost Number: 1 Registered: Aug-04 | i cant access to the link either can anybody help me please ` or you can send me the fix by mail at : felixdesc@hotmail.com thx for the support |
||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 89 Registered: Jun-04 | Ftp access to ftp://fryguy.ca is anonymous access with e-mail as your pasword (real or fake) you may need to enable or disable passave ftp in your client or web browser. Internet explorer will automaticly use anonymous with the password IE@ by default. so you just need to change to use passive ftp transfers (If your behind a firewall or use dsl or cable then changing this will most likely be needed) To change for IE go to: tools/internet options then the advanced tab scroll down to where you see "use passive ftp (for firewall and DSL modem compatability)" place or remove the check mark and apply. then try the site it should now work. |
||
|
New member Username: Marty777North'd, Pa Usa Post Number: 3 Registered: Aug-04 | Can someone help. I just get a couple of channels on my silverbullet enforcer. | ||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 90 Registered: Jun-04 | didn't i solve you key problem by instant message? mabe a different person? | ||
|
Anonymous | your silver bullet is the same thing as a blackbird...go to blackbird.cx site and get the new fix | ||
|
New member Username: ServersPost Number: 1 Registered: Aug-04 | hey people i need the new keys if you can help me find them do any thing to get them | ||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 91 Registered: Jun-04 | Dishnetwork Key 0 is active, changed THUR FEB 19, 2004 KEY0: 06 07 F0 E2 61 6F E1 45 KEY1: C2 66 46 F8 7A 73 48 2A ExpressVu AUX 1 is active, changed Mon 17 NOV 2003 05:05:00 PM EST AUX0: 82 D7 51 E4 5B 97 9D 81 AUX1: 65 57 46 14 36 02 D8 DA |
||
|
New member Username: ServersPost Number: 2 Registered: Aug-04 | COOL IT WORKS THE KEYS KEYS WORK | ||
|
Unregistered guest | i cant download the fix for atmega 128, the page doesn't load. can anyone help??? my email adress is ingenious_9@msn.com | ||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 93 Registered: Jun-04 | My ISP was doing a upgrade and my IP address changed,so it was the DNS pointing to my sites IP address that was causing my site to not work, should be up by now. Glad the keys worked. | ||
|
sgtppr36 Unregistered guest | im having trouble using jeepers, i follow all the steps to set it up , but when i want to read or do the full monty, i get an error message saying "failure to enter program mode"....can anyone please help, im using AT90S8515 card if that means anything | ||
|
wabana Unregistered guest | Help. I had my card programmed and the individual who programmed it is not longer in the business. what hardware and software do I need to program the card myself (this is not atmega board) | ||
|
just visiting Unregistered guest | The new program out their for atmega is NNW23 it support parity key, PK0. That is all.. | ||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 98 Registered: Jun-04 | sgtppr36, you have the wrong card for this fix. If your card has a AT90S8515 chip you have a AVR card. You need the lazyboyz1.pfg for the AVR cards. | ||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 99 Registered: Jun-04 | wabana, you need to tell me what type of testing device your using for me to give you list of required equiptment. |
||
|
Bronze Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 100 Registered: Jun-04 | There is a "NNW23.pfg" going around but ppl are saying its a re-name of the origional fix "Juggalo_X's_Mod.pfg" this is the first fix (I would have to compare them with a md5 hash or a handy program i have that shows differences in files). I have "Juggalo_X's_Mod.pfg" and it works perfectly on all channels. (Either fix will work for you) |
||
|
Pete Unregistered guest | Hi there, i have a 3100 with an Atmega128 and whatever witch pfg i use, i always have the message "Your smarcard doesn't allow you to view this channel .. bla blah blah" it happen time to time, otherwise i have access to all channel. It's just that this is anoying me alot .. i have to power off and up than i have access again. Here the pfg i tried: Atmega 1.3b Atmega 1.4 Jugalo_x's_mod Angel Vision V1 NNw21D-pfg Chatternut09 Any idea to help me ? |
||
|
poty Unregistered guest | is bev still up ? | ||
|
Pete Unregistered guest | yep | ||
|
Silver Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 104 Registered: Jun-04 | Pete, do you have a d-lock on that IRD ? | ||
|
wabana Unregistered guest | Johathon, all I know is that I have an expressvu receiver with a digital lock on it and the original card is programmed | ||
|
Silver Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 106 Registered: Jun-04 | You need the fix for your plastic(CAM). I dont do plastic cards, Nor do i know where the nagra fix is for them. | ||
|
sgtppr Unregistered guest | i finally got jeepers to work for me and was able to get the full monty to go, but now whenever i put in the card in the ird im getting an error "smart card not inserted"...is there something im missing or doing wrong ? | ||
|
Silver Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 107 Registered: Jun-04 | usualy a indication that your IRD#,or BOXKEY# is wrong. A wrong CAM# usualy just causes a black picture but can cause the same message. Double check your #'s generate a new CAM ID with Scammers2 and do a verify and read from the card to be sure its programing properly. | ||
|
Unregistered guest | Does anyone know how to fix a AVR Atmega for a 3500 model | ||
|
sgtppr Unregistered guest | ok, im hoping this will be my last post, after much frustration, i've finally been able to get everything set up, but now when i put the card in, i get a full guide, and headers on the screen , but all the channels are black, ive tried several times with the same result , is there a patch or something im missing | ||
|
poty Unregistered guest | me to i get no pic and sound | ||
|
Silver Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 108 Registered: Jun-04 | melissa_dorina, nope because a AVR and Atmega are two different cards. |
||
|
Silver Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 109 Registered: Jun-04 | sgtppr, check your public keys, IRD# and BoxKeys. I'm also assuming that your using the latest .pfg fix for your card (Atmega?) |
||
|
Silver Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 110 Registered: Jun-04 | poty, you too check your numbers and next time be more specific "me to i get no pic and sound" dont tell me anything other then you have a problem. Whats your setup your using ? AVR, Atmega, Plastic, EMU, MagicCard ? |
||
|
just a newbie Unregistered guest | plastic rom 10 | ||
|
just a newbie Unregistered guest | plastic | ||
|
Anonymous | Having trouble getting my card to work i think its and AVR for BEV. When I program it and insert it in the receiver the menu and program guide work but when i go to a channel the screen is black. I've tried many programs and i can't get it to work. I need help!! | ||
|
New member Username: LonewolfUnited states United states Post Number: 8 Registered: Aug-04 | anonymous are u using a magic card? ck out ur recvs info and make sure everything is correct and ck out |
||
|
Anonymous | No the card is and AVR. I just need to know what program to use, how to get it and what i need to know about the IRD, Cam#, etc Thanks | ||
|
Bronze Member Username: LonewolfUnited states United states Post Number: 12 Registered: Aug-04 | anonymous sorry about that listen dsscentral.net also has alot of info and free downloads maybe u can find ur answer there. good luck! | ||
|
Silver Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 135 Registered: Jun-04 | LazyBoyz1.pfg is the latest AVR fix for bell. | ||
|
Bronze Member Username: LonewolfUnited states United states Post Number: 15 Registered: Aug-04 | thanx for the help out jonathan! | ||
|
Anonymous | I know for sure that the card is an AVR3 now. I tried the lazyboyz program and i lost the black screens and the errors but evry channel is blocked and red on the guide. Is there something i'm missing. Also i do not have a subscription if that matters | ||
|
Silver Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 141 Registered: Jun-04 | use the LazyBoyz1.pfg for your avr and check all your #'s and be sure to have the latest keys. It will work when done with the right #'s. | ||
|
Silver Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 142 Registered: Jun-04 | just check you box keys, also hit sys info on your remote and if you have location ID 0000001 let me know. | ||
|
Anonymous | NO the location ID is not 0000001 | ||
|
Silver Member Username: FryguyBarrington Passage, Nova Scotia Canada Post Number: 145 Registered: Jun-04 | Ok, so its just that you have a number wrong (IRD#,CAM#,Keys) or the active public key is set wrong. be sure the numbers are right and that the contacts are clean on your cards (AVR and CAM) for your AVR married-sub. | ||
|
grapewine Unregistered guest | Hy anyone, I have the same screen runing again and again. On the sreen I have the mesage "attention, please standby for the satellite signal thank you for your patience at the bottom Satellite:Default transponder changing continuously progress: 0 of five. My receiver is a 3100, and I have a TSOP lock, I use an ATMEGA 128. What should I do to get ride of that message and to prevent it to happen again? | ||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 146 Registered: Jun-04 | grapewine, I'm assuming you have the latest fix on the atmega. Get to the system info screen (sys info button on the remote) and your firmware should be E469. If its not un-plug your IRD and turn your locks off. Plug back in. Then you have to wait with the power off (without the green light on but still pluged in) for it to update (green led will come on but with no picture then start blinking) this can take some time (10 min to a few hours or so). The easiest way to update it to do a erace of SA3 with a j-tag and j-keys. This will force it to take an update. also while your on the sys info check if your location ID is 0000001 i doubt this is the case. post your findings please. |
||
|
grapewine Unregistered guest | Jonathan fry, my firmware is E469 and my ID is not 0000001. however on the sys info screen I have "new card ready" in green??? DNASPO10 revA81. | ||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 148 Registered: Jun-04 | minu 6,1,1 and be sure that "Nimiq 91" is selected and do a check switch also. If you have no signal strength try changing the transponders to see if you have anything at all. If not then check your wires. | ||
|
Anonymous | IM pretty sure im geetin the right numbers but i still get a black screen. I was wondering if you could tell me the numbers i need to use. Thank You |
||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 152 Registered: Jun-04 | Sure, just send me your IRD and card and I'll fix it for you. Its half intended as a joke but also a offer to help. The reason is that if you cant fix it i basicly ned the IRD here to do the advanced trouble shooting to fix it. (pay for shipping "with insurance" + $20 labour + price of replacement part "I will contact with price for approval first") GENERAL PROBLEMS: There are problems like firmware issues, TSOP ECM hits, improper Atmega lock/fuse bits (caused by anything because the card is powered to the lowest voltage the chip can run at, cause alot of problems in programing stage), D-lock falure, then some other starnge problems of a combination of things. |
||
|
exspider Unregistered guest | please help I'm a newbies. what is atmel not part of atmega 128 when i try to do a full monty and why is board selection is jeeper new fix progam is clk 18.00mhz and why does my cam id have 12 number. my crystal 184ecsn does that mean 18.4320Mhz |
||
|
exspider Unregistered guest | please help I'm a newbies. what is atmel part is not an atmega 128 when i try to do a full monty and why is board selection is jeeper new fix progam is clk 18.00mhz and why does my cam id have 12 number |
||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 153 Registered: Jun-04 | Your crystal is 18.432Mhz, the CAM ID with 12 numbers heck knows. The atmel part is not an atmega 128 that can be the lock/fuse bits or the Atmega chip is gone. | ||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 154 Registered: Jun-04 | Try this: "Lock/fuse settings Here is the lock settings for the ATMega 128 and a little proceedure that helps set these back to default. LOCK BITS - all checked FUSE LOW - All checked but BODEN and SUT0 FUSE HI - OCDEN, EESAVE, BOOTRST FUSE EXTENDED - both checked [FF][AF][89][FF] ALONG THE BOTTOM 1. Load up jeepers, and plug everything in for your atmega as normal (ie atmega in programmer, plug cable into compurer) 2. make sure jumper is ON 3. click the atmel tab, ATmega128, erase/flash eeprom 4. when it says erasing eeprom, PULL THE JUMPER 5. Do this 3 or more times 6. then do full monty, when it says erasing eeprom, PULL THE JUMPER, and when it says writing, PUT THE JUMPER BACK ON 7. You will get errors, go back and repeat steps 3 to 6. You will notice that each time you do the full monty, you will write a little more to the card before you get an error. 8. eventually you will write the card, and you will be able to erase the eeprom WITHOUT PULLING THE JUMPER 9. your atmega is fixed. Always program at the correct frequency Some people had to do this 2~5 times others I have heard take up to 20 times....Good luck." |
||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 157 Registered: Jun-04 | Just to let you know that if its the last two numbers of your IRD# and CAM# that your missing thats because its not needed it should be -XX in jeepers (jeepers will do that automaticly) | ||
|
exspider Unregistered guest | thank jonathan but how do i set the lock fuse to default when it a jumpless atmega board. in jeepers program at the board selection is clk 18.4320Mhz the same as atmega 128 18.4320Mhz |
||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 160 Registered: Jun-04 | Quote "but how do i set the lock fuse to default when it a jumpless atmega board." Lock fuse settings are set in jeepers not a jumper on the card. Quote: "in jeepers program at the board selection is clk 18.4320Mhz the same as atmega 128 18.4320Mhz" 18.432Mhz is 18.432Mhz! Atmega128 is the chip on the card. |
||
|
exspider Unregistered guest | 2. make sure jumper is ON 3. click the atmel tab, ATmega128, erase/flash eeprom 4. when it says erasing eeprom, PULL THE JUMPER so pull the jumper doesn't mean the jumper on the atmega board |
||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 161 Registered: Jun-04 | LOL yah. If you dont have a jumpered card then you can do that step and that only to help try to recover a dead card. Just check your lock/fuse bits and see if you can change them. If not and you cant get it to do sh*t all then your card is toast. | ||
|
Baxter Unregistered guest | Hi guys have a AVR with the Lazyboyz upgrade programed and I get the guide etc. but get the message that smart card does not have authorization. Anything I am missing. | ||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 169 Registered: Jun-04 | yep, thats why its not working. Double check all your #'s and full monty again. | ||
|
Unregistered guest | Help! Need an update for an Atmega 128 card. Satelite only lasts about an hour and then when I restarted, it goes back to the Technical update page. And this is happening after I did Jonathan Fry's update from his posting in August. Thank you. | ||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 171 Registered: Jun-04 | That fix works, so be sure to have a valid ROM3 CAM ID, (generate with scammers2)and use a valid US zip code (Use scammers2 it will show in the bottom left your zip code)one of your numbers must be invalid and its getting hit. | ||
|
Unregistered guest | Hi I have a 2700A bev reciver with a rom 11 card but have been unable to program avr 6 card to work with it also have 3120 doing same just purchase both what do I need Help | ||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 186 Registered: Jun-04 | A new card, the AVR cards are old technology and will not work in the future. If you're comfortable with the AVR card the new Atmega128 cards will be the same thing other then you don't need a plastic CAM with it, it replaces the plastic CAM the came with the receiver. And is the same size as the original CAM. You will also need a j-tag to get the box key and backup your TSOP (receivers firmware)and a D-lock (prevents a ECM from rewriting the firmware turning your receiver into a rock each time a ecm hits and saves you from j-taging all the time ecm season hits) hope that helps answer your question. | ||
|
tonymontana Unregistered guest | Hello everyone,I used Juggalo_X's mod.pfg for 1 month now and It worked until yesterday. Suddenly I lost my signal and then nothing This afternoon,the signal came back but with only the TV guide..BLACK SCREEN and NO SOUND!!! Could someone help me? |
||
|
tonymontana Unregistered guest | I have a 3100 receiver and using Atmega | ||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 196 Registered: Jun-04 | Hit your system info button on the remote and if you have location ID 00000001 you have been hit by an ECM (electronic counter measure) and it has disabled your receiver. It's been in the stream as of Thursday September 16th that was originally reported and confirmed. You may have been a victim to an ECM. Check and let me know. | ||
|
tonymontana Unregistered guest | hello FryGuy,NO I have location ID:40820660 Software : E469EAED-N Boot trap: 12ABEAED but its strange,I have NEW CARD READY in green! |
||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 197 Registered: Jun-04 | Then you good to go with the receiver. That means that its got to be the card. Check your numbers and use a valid ROM3 CAM ID (generate one with scammers2)and be sure all your numbers are right and Full Monty, then you should be good to go again. | ||
|
tonymontana Unregistered guest | by the way,which fix should I use? Could u give me a fix ? |
||
|
tonymontana Unregistered guest | I just tried a fix called "Latest_Atmega-128_FIX_Juggalo_X's_Mod.pfg" and I did the stuff with the scammers2 but It didnt work.. Still have the guide,but no image and NO SOUND! |
||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 198 Registered: Jun-04 | Sorry but thats the .pfg that is working right now. If its not working for you then you need to do a full erace of your card to restore it to a virgin state then do a full monty. | ||
|
tonymontana Unregistered guest | FryGuy,how could I do a Full erase of the card? After doing that,is the Full Monty the same processus that I used to do? Please,tell me how to full erase the card? |
||
|
tonymontana Unregistered guest | FryGuy.ca,is it normal?I only have the channel 198 that is working. Dont forget to tell how to FUll erase the card |
||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 199 Registered: Jun-04 | The channel 198 is normal thats in the clear by bev you'll allways have that channel. To full erace to virgin state you need the Flash.hex and Eeprom.eep files to write to the atmega.
|
||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 200 Registered: Jun-04 | To use go to atmel/atmega128/ and select write flash then select the flash.hex when done do the same again go to atmel/atmega128/ but select write eeprom and then select the eeprom.eep. now check the lock/fuse bits ans input your numbers and hit full monty when everything looks good. | ||
|
tonymontana Unregistered guest | Thaanks FryGuy.ca,but tell me something,Should I 1)re-use "Latest_Atmega-128_FIX_Juggalo_X's_Mod.pfg" as the FIX? 2)How do u do the check the lock/fuse bits and input ur numbers? I really appreciate the time that you putting by helping me. Tks a lot FryGuy |
||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 201 Registered: Jun-04 | Yes its still the working .pfg for BEV. Lock/fuse bits go to atmel/atmega128/ select lock/fuse bits to set them. LOCK BITS - all checked FUSE LOW - All checked but BODEN and SUT0 FUSE HI - OCDEN, EESAVE, BOOTRST FUSE EXTENDED - both checked |
||
|
tonymontana Unregistered guest | FryGuy,I did what u explained but nothing worked..Still have the Guide but NO IMAGE and NO SOUND! 1-I write flash then select the flash.hex 2-I write eeprom and then select the eeprom.eep 3-BUT I MAY HAVE MADE A MISTAKE concerning the Lock/fuse. Because when u say "Check the lock/fuse and input your numbers",I did so by doing: Atmel-->Atmega128-->Lock/fuse settings right? But after that,I saw the number and just replace the 2nd column with [AF],because I saw that in the Fix folder([FF][AF][89][FF])... What went wrong? |
||
|
tonymontana Unregistered guest | ok,I just read your 2-10AM update,I did it but nothing works?Dont understand why? | ||
|
Anonymous | I need a fix for my 2700 and 3100 bev it must be able to work with an autoroll i tryed looking in every site for pirating bev. | ||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 207 Registered: Jun-04 | Why does it need to have autoroll? Most new .pfg's for jeepers do autoroll as most people have autoroll cards. But why does it matter? BEV hasn't rolled the keys in a LONG time! so either way it dont matter if it does or not, as it hasn't been changing. Just use the fix thats been working all along fron the aug 14th on. |
||
|
bedy Unregistered guest | hey fryguy have you heard anything about nimiq 3 bell is swithcing to this starting september 30. All channel setup will change and everything will be wipe out. |
||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 211 Registered: Jun-04 | I didn't even know they had a new bird in the sky. I know that later on they will switch to nagra2 ciphering / encryption after the card swap is complete. | ||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 212 Registered: Jun-04 | tonymontana, were you able to write the lock/fuse bits? and have you confirmed that your actually writing contents to the flash memory on the Atmega? | ||
|
New member Username: RobturleyPost Number: 1 Registered: Sep-04 | I tried flashing my card using the information above (lock bits, hex, eeprom file) and now I cannot edit the IRD or Box Key fields and get an "Error Writing to flash memory" error. Any suggestions? |
||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 213 Registered: Jun-04 | Your card is DOA get a new one. It is a locked card now if you cant change the lock/fuse bits therefore useless garbage. | ||
|
tonymontana Unregistered guest | hello FryGuy,my caard is working since 2 days...U going to make fun of me..the problem was my boxkeys.. | ||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 216 Registered: Jun-04 | I can't make fun of that because i've done it before too. Glad you figured it out. | ||
|
Jakester Unregistered guest | I am a newbie and need some help and hoping someone out there can assist. I got ecm'ed and was using jkeys to erase the ird specific address, but erased full by mistake. I have never been able to write a .bin file, as my jkeys always seems to hang up. Now, my IRD will not even power on. Is there hope? Thanks |
||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 217 Registered: Jun-04 | Ooopsie, I guess. I hope you made a backup first. Then just write your .bin back to the receiver. What model IRD, if you dont have the .bin for your TSOP i got a rather large collection of TSOP dumps collected. I'm sure i got one that can be used with a slight editing with TsopEdit (easiest way to edit the TSOP .bin) or a hex editor of your choice (Very hard and confusing if your new and depending on the program). It can be fixed the green light is software controled 'similar to an old computer it has software or firmware thats stored on the TSOP = "Thin Small Outline Package" its a Memory chip' its just a indicator that the receiver isn't 'booted up' because it dont have the software to 'bootup' anymore. | ||
|
cheeks Unregistered guest | Need a fix for BEV. Have Atmega 128 card. Have used your fix FryGuy since August. Now getting errors since they changed all the channels. Is there a new fix around?? | ||
|
New member Username: NotsokrzyPost Number: 1 Registered: Sep-04 | I used to be able to get some (More like 3) chinese channels wayyy back when (851, 852, 853 to be exact). But for some reason I can not seem to get those anymore, I have all the other channels and seems to be working fine. Considering my parents only understand the Chinese channels, is there any way I can get them back?? I have an EchoStar 2800 with an Atmega 128 card. Any help would be thankful. | ||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 224 Registered: Jun-04 | cheeks, simply program your card again and change the CAM ID (generate a ROM3 CAM ID with scammers2). Then full monty with the new CAM ID all your other numbers stay the same. | ||
|
New member Username: FtasteveSandusky, Ohio USA Post Number: 1 Registered: Sep-04 | I have a fortec lifetime ultra. Using it on DN. What do I have to do to watch BEV as well - like at the same time? I know an additional sat dish in the 91 position. But what about the keys? Any and all help will be appreciated. | ||
|
Anonymous | don't worry about the keys...it'll grab em!!!! | ||
|
Unregistered guest | can someone help me when i put the card in my reciver when i select a channel its just come black screen i think i have to get new keys can someone tell me the new keys. "please" send me email on arslannaseer@hotmail.com or arslannaseer20022001@yahoo.com | ||
|
cheeks Unregistered guest | Thanks FryGuy-will give that a try. | ||
|
Unregistered guest | I'm Having trouble with my AVR3 on an BEV 3100 I'm using jeepers and scammer V2 to get my cam ID, Auxs and using the newest toadcode cfg and still i'm getting a full channel list with no sound or picture Ihave double checked my keys they all looked good my reciever's software is up to date and the CAM is married to it I'm lost | ||
|
devdas880 Unregistered guest | Can someone help me with this problem? I have a rom 11 card# S 00 3016 8264 78 It is a yellow dish 500 card. I do not have the password to make changes to the card. Is there anything I can do to get access to the data on the card. Thanks in advance |
||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 324 Registered: Jun-04 | You'll need to take it to a dealer and get it opened (brute force opened) so it can be programed. | ||
|
Anonymous | Hi all, I came across this board by accident and it looks like there are some very knowledgeable people here. I know very little about hacking, so I hope this question doesn't seem to stupid. I understand that BEV is going to the Nagra2 cards. I'm running plastic now and have lost the HD channels and soon will loose Venus. Is there a way to get those channels on the Nagra card? Also, is there anything out now or in the works for when all of the old cards are swapped out? |
||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 330 Registered: Jun-04 | That's not a stupid question by far! Many people are asking the same thing in the back of their mind and so am I. Unfortunately I haven't found anything yet or caught wind of any development ideas in progress with nagra2. If anyone has any information please post it for other inquiring minds. | ||
|
Unregistered guest | bell has new cards there called all access cards in there dishes and i cant get then to go, all i get is a black screen | ||
|
Anonymous | how do u get rid of the blue screen glitch | ||
|
New member Username: FaprilPost Number: 1 Registered: Nov-04 | Help..I spent 400$ for nothing! I bought a dish 811 receiver this summer and tried to activate it with Bell last week (after starchoice contract was over) and was told THEY CANNOT ACTIVATE IT !!! It's identical but supposedly, the software inside is different. I<m pissed off! Is there a way to get BEV working on this? It's a CARDLESS model but there is a slot for potentially using a card...not sure what its used for...since it's supposed to be cardless. Atmega? rs232 with a software? what can I do. I not really interested in suscribing to dishnet either but will need to consider doing so... Thx. |
||
|
New member Username: FaprilPost Number: 2 Registered: Nov-04 | oups..forgot to say that it's identical to Bell's 6120 model.. but the software inside is supposedly different. | ||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 369 Registered: Jun-04 | IF you can j-tag it flash it with the BEV firmware (be sure to use the right bootstrap compared to the old firmware). Once that's done then you should be able to activate it just like it was a BEV 6120 but not so fast its not that easy. The IRD being card less is the problem mainly if it's been activated before. If so then it's married to the IRD and your sh*t out of luck. |
||
|
Anonymous | those units can't be jtag'ed, they use multilayered pcbs. at the present time they're unhackable. | ||
|
Anonymous | also the smartcard chip is embedded in the motherboard so even if you could jtag it and put bev firmware on it, you'd have to rewrite the smartchip with a bev rom image. say you could rewrite the chip which is a nagra 2 romX (currently impossible) you'd have to get a legit rom image off an unused or exsubbed bev 6120. in other words, take a loss and pick up the 6120, or sub to DISH with US addy. | ||
|
New member Username: FaprilPost Number: 3 Registered: Nov-04 | I guess if Bell would'nt be so stubborn and would reprogram it in their lab, it would all work well. It's a virgin unit and they should be more flexible for that but hey, I guess I will have to sub to dish. I will have to swallow my pride since I'm a beginer and don't know what equipement I need to J-tag and reprogram the unit. How much is the equipment for that? Thanks all. | ||
|
Anonymous | bell has new cards there called all access cards in there dishes and i cant get then to go, all i get is a black screen. Maby this time someone will answer me! | ||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 470 Registered: Jun-04 | Thats right its called a access card , the technical name is a CAM (Conditional Access Module). If you post a question with "all i get is a black screen" we need more info on your system and setup to answer it or suggest a soloution. (Whats your system, card type, testing method, what have you done, current configuration, etc.) |
||
|
tonymontana Unregistered guest | Hello Fry,Having a problem here...using an Atmega,3100 receiver..dont understand why but having black screen since yesterday.. | ||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 481 Registered: Jun-04 | Strange, I heard some others have had problems but it's not wide spread yet. Have you beee=n hit by and ECM? Check by hitting the "sys info" button on your remote, if it says location ID 00000001 then you have been hit. | ||
|
tonymontana Unregistered guest | Ive checked the ID location but Im not hit..I dont understand why?Every 30 mn,the image freezes and there's a message saying: Your card is not inserted! | ||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 514 Registered: Jun-04 | Invalid ROM3 CAM ID. Generate one with scammers2.exe then full monty your card again. | ||
|
Unregistered guest | Hi guys I am wondering, has anyone heard what has happen to dsshelper? I tried to go to site afew times this weekend and nothing. thanks |
||
|
Bronze Member Username: Knee_growDetroit Post Number: 97 Registered: Jan-05 | Who Cares? | ||
|
Silver Member Username: FryguyNova Scotia Canada Post Number: 540 Registered: Jun-04 | Thats not a way to answer anyone, Knee grow. But I do agree in a way. There are many other web sites for information that are available. Like www.sattech.ca. | ||
|
largo key Unregistered guest | kenno...here's what was posted at dsshelper: This website is officially closed! 01.10.05 Due to reasons beyond even my comprehension this website is now closed. You wanna know why, go ask SNV or Betty, I'm sure they'll have a lie to tell ya ) Make sure they tell ya how they locked me out of my own server, so they could steal the database and take it for their own using. These guys are backstabbing azzholes who would fock over their own mother if it benefitted them. If by chance DSS Helper's database or forums shows up on the web somewhere, you can blame these two priks, and know that it was taken without the my consent. I personally have destroyed all data related to DSS Helper that was stored on my personal computer, and as much as I could off the server. By the way fellas, fock off, I can't wait 'til yours comes around! You can have the server, the name will always be mine! To those of you that supported this website over the years I love all of you. It has been an amazing ride. As far as the whole Helper Crew, you guys are amazing, everybody that helped make this place what it was. I never thought in a million years that we would come this far. I'm sure you all have you own idea about me, but like I said, go ask SNV and Betty, It's always easier hearing one side of every story. If you continue to associate with these thiefs, use caution guys, just think how easy it was for them to screw me over, they'll do the same to you. I miss this place already, almost feels like a relative passed. I will miss all of you, all the newbies and their repetitive questions, and of course who will ever forget Paldo "The Sheep Fooker", and Coyote and that dolphin sex story. There has been some great times here, but all good things must come to an end it seems. It's been real! RabbiT - DSS Helper Owner and Admin There are many other sites as fryguy suggested..[link removed] is one of them reputable sites also. BTW..I had to edit a few choice words above to allow the post. |
UploadMain Forums
Today's Posts- Home Audio Forum
- Home Video Forum
- Home Theater Forum
- Car Audio Forum
- Accessories Forum
- All Forum Topics